A 2.5-m-long wire carrying 3.9 A is wound into a tight coil 6.0 cm in diameter. Find the magnetic field at its center. B =_____

Answer: v=1,56(m/s)

Explanation: Called: g(Gravity acceleration) =10[tex]m/s^{2} \\[/tex](or 9,8[tex]m/s^{2}[/tex])

                                 h=1,2m  ;   t=1,3s

Because the coin fell freely, the velocity is calculated by the formula:

v=[tex]\sqrt{2gh}[/tex]  (1)

besides, you have time to touch the bottom of the water is 1,3s:

t=[tex]\sqrt\frac{2g}{h} }[/tex] (2)

(1) and (2) => v=1,56 (m/s)

The volume will the air have at cruising altitude at the same temperature (body temperature) if cabin pressure drops to 7.50 × 10⁴ Pa and no air leaves their stomach is 162 cm³.

To determine the volume of air in the passenger's stomach at cruising altitude, we need to consider the initial and final pressure. The initial volume is 120 cm³ and the cabin pressure at cruising altitude is 7.50 × 10⁴ Pa. We can use Boyle's law, which states that the product of pressure and volume remains constant when temperature is constant: P₁V₁ = P₂V₂.

However, we first need to determine the initial pressure at sea level. Standard atmospheric pressure at sea level is approximately 1.013 × 10⁵ Pa. Now we can use Boyle's law:
(1.013 × 10⁵ Pa)(120 cm³) = (7.50 × 10⁴ Pa)(V₂)

To solve for V₂, the final volume at cruising altitude:

V₂ = (1.013 × 10⁵ Pa)(120 cm³) / (7.50 × 10⁴ Pa)

≈ 162 cm³

So, the volume of air in the passenger's stomach at cruising altitude at the same temperature will be approximately 162 cm³.

Learn more about air volume: https://brainly.com/question/14602582

#SPJ11

R0 is used to calculate this velocity because it represents a distance related to the particle's motion. By incorporating it into the equation, we can determine the initial velocity (vpi) based on the distance (Ro) and the height (h) under the influence of gravity (g).

In the given equation, po represents the force exerted on the fluid by the piston, mp represents the mass of the piston and vpi represents the velocity of the piston.

To calculate vpi, we can rearrange the equation as:

vpi = po/mp

We know that the force exerted on the fluid by the piston is equal to the weight of the column of fluid above it. Therefore, we can substitute po with ρghA, where ρ is the density of the fluid, g is the acceleration due to gravity, h is the height of the fluid column above the piston and A is the cross-sectional area of the piston.

vpi = (ρghA)/mp

We can simplify this equation further by substituting A with πR0^2, where R0 is the radius of the piston.

vpi = (ρghπR0^2)/mp

Now, we can substitute mp with ρπR0^2t, where t is the thickness of the piston.

vpi = (ρghπR0^2)/(ρπR0^2t)

Simplifying further, we get:

vpi = gh/2t

Finally, we can substitute t with R0/2 to get:

vpi = Ro√g/2h

Therefore, R0 was used in the calculation of vpi because it is the radius of the piston, which determines the cross-sectional area of the piston and hence the force exerted on the fluid.

Learn more about velocity here:

https://brainly.com/question/17127206

#SPJ11

Therefore, the magnetic field strength of the EM wave is [tex]3.54 * 10^{-8}[/tex] T.

a) The electric field strength of the electromagnetic (EM) wave, we can use the equation:

I = [tex]ce_oE^2/2[/tex]

Here I is the intensity, c is the speed of light, ε0 is the permittivity of free space, and E is the electric field strength.

Rearranging this equation to solve for E, we get:

E = [tex]\sqrt{(2I/(ce_0))}[/tex]

Substituting the given values, we get:

E = [tex]\sqrt{(2 * 300 / (3 * 10^8 * 8.85 * 10^{-12}))}[/tex] = 102.6 V/m

Therefore, the electric field strength of the EM wave is 102.6 V/m.

b) The magnetic field strength of the EM wave, we can use the equation:

B = [tex]\sqrt{(u_0e_0)E}[/tex]

Here B is the magnetic field strength, μ0 is the permeability of free space, and E is the electric field strength.

Substituting the given values, we get:

B = [tex]\sqrt{4 * pi * 10^{-7} * 8.85 * 10^{-12)} * 102.6 }[/tex]

= [tex]3.54 x 10^{-8[/tex] T

Learn more about magnetic field visit: brainly.com/question/14411049

#SPJ4

An image formed when light rays do not actually pass through the image location and would not appear on paper or film placed at that location is referred to as a "virtual image".

Virtual images are formed by the apparent intersection of light rays, which cannot be projected onto a surface, unlike real images. A virtual image is formed when the light rays appear to be coming from a particular location, but they do not actually converge at that location. Instead, they diverge or appear to be coming from a different location, creating the illusion of an image that would not be visible on paper or film placed at the location where the virtual image appears.

This phenomenon can be observed in mirrors, lenses, and other optical devices that reflect or refract light.

To know more about virtual image, visit:

https://brainly.com/question/12538517

#SPJ11

The image is located 12cm behind the mirror and is real, inverted, and enlarged.

To locate the image of an object placed in front of a concave mirror, we can use the mirror equation:

1/f = 1/do + 1/di

where f is the focal length of the mirror, do is the object distance (distance of the object from the mirror), and di is the image distance (distance of the image from the mirror).

Given that the object is located 4cm in front of a concave mirror with a radius of curvature of 12cm, we can determine the focal length of the mirror as follows:

f = R/2 = 12/2 = 6 cm

Substituting the values into the mirror equation, we get:

1/6 = 1/4 + 1/di

Solving for di, we get:

di = 12 cm

This means that the image is located 12 cm behind the mirror, on the same side as the object. The image is real, inverted, and enlarged.

To confirm our answer, we can draw a ray diagram as follows:

1. Draw the principal axis of the mirror (a straight line passing through the center of curvature C and the vertex V of the mirror).

2. Draw the incident ray from the top of the object parallel to the principal axis, which reflects off the mirror and passes through the focal point F on the principal axis.

3. Draw the incident ray from the top of the object passing through the focal point F, which reflects off the mirror and becomes parallel to the principal axis.

4. Draw the reflected rays to find the location and size of the image. The reflected rays will intersect at a point 12cm behind the mirror, on the same side as the object, forming a real, inverted, and enlarged image.

Therefore, The real, inverted, and magnified image is 12 cm behind the mirror.

To learn more about laws of reflection click:

https://brainly.com/question/13101215

#SPJ1

The average power delivered to the circuit is 4.12 W.

The maximum power delivered to the circuit is 4.13 W.

To find the average power delivered to the circuit, we can use the formula P = V^2/R, where P is power, V is voltage, and R is resistance (in Ohms).
Using the given values, we have:
P = \farc{(121V)^{2}{ 3.53 k-Ohm }
P = 4,119 mW or 4.12 W (rounded to two decimal places)
Therefore, the average power delivered to the circuit is 4.12 W.
To find the maximum power delivered to the circuit, we know that it occurs when the resistance is equal to the generator's internal resistance (which we don't know). However, we can use the formula P = V^2 / (4R), where R is the total resistance in the circuit (the 3.53 k-Ohm resistor and the generator's internal resistance).
Assuming the internal resistance of the generator is negligible compared to the 3.53 k-Ohm resistor, we have:
R = 3.53 k-Ohm + 0 Ohm (generator internal resistance)
R = 3.53 k-Ohm
P = \frac{(121V)^{2 }{ (4 * 3.53 k-Ohm)}
P = 4,133 m W or 4.13 W (rounded to two decimal places)

learn more about resistance Refer: https://brainly.com/question/9605409

#SPJ11

The net work done is equal to the change in kinetic energy, the net work done on the box is 512 Joules.

To find the net work done on the box, we will use the work-energy theorem, which states that the net work done on an object is equal to its change in kinetic energy.
First, let's find the final velocity of the box after 4 seconds of acceleration. We can use the formula:
v = u + at
where v is the final velocity, u is the initial velocity (0 m/s since it starts from rest), a is the acceleration (4 m/s²), and t is the time (4 s). Plugging in the values, we get:
v = 0 + (4 m/s²)(4 s) = 16 m/s
Now, we can find the change in kinetic energy using the formula:
ΔKE = 0.5 * m * (v² - u²)
where ΔKE is the change in kinetic energy, m is the mass (4 kg), v is the final velocity (16 m/s), and u is the initial velocity (0 m/s). Plugging in the values, we get:
ΔKE = 0.5 * 4 kg * (16 m/s)² - 0 = 512 J
Since the net work done is equal to the change in kinetic energy, the net work done on the box is 512 Joules.

Learn more about kinetic energy :

https://brainly.com/question/26472013

#SPJ11

When the slit spacing in a diffraction grating increases, so does the distance between neighboring slits. As a result, the number of slits per unit length decreases, causing the diffraction pattern to widen out.

Light is diffracted by each individual slit in a diffraction grating, and the diffracted waves interact constructively or destructively to generate a diffraction pattern. The phase difference between the waves is determined by the distance between the slits, which influences the interference pattern.

The interference pattern grows increasingly spread out as the slit spacing rises, as does the distance between the brilliant fringes. This implies that the diffraction grating may resolve spectral lines that are closer together, resulting in increased spectral resolution. Increasing the slit spacing, on the other hand, reduces the intensity of the diffracted light since less light goes through each individual slit.

Overall, increasing the slit spacing alters the physical configuration of the diffraction grating by changing the interference pattern and spectral resolution, as well as the intensity of the diffracted light.

Learn more about Diffraction:

https://brainly.com/question/30035662

#SPJ4

The values of rm and xm can vary with applied voltage due to changes in the operating conditions of the system, which can affect the resistance and reactance of the system's equivalent circuit.

The values of rm and xm can vary with applied voltage in certain electrical systems because they are dependent on the operating conditions of the system.

In an electrical system, the values of rm and xm represent the resistance and reactance of the system's equivalent circuit, respectively. The equivalent circuit takes into account the various components of the system, including the resistance and inductance of the conductors, the capacitance between conductors, and the impedance of any connected loads.

When an electrical system is subjected to a varying voltage, the current flowing through the system will also vary, and this can cause changes in the system's operating conditions. For example, as the voltage increases, the current flowing through the conductors may increase, which can cause the temperature of the conductors to rise. This increase in temperature can cause the resistance of the conductors to increase, which, in turn, can cause the value of rm to increase.

Similarly, changes in the current flowing through the system can also affect the reactance of the system. For example, as the current increases, the magnetic field around the conductors may also increase, which can cause the inductance of the conductors to increase. This increase in inductance can cause the value of xm to increase.

Therefore, the values of rm and xm can vary with applied voltage due to changes in the operating conditions of the system, which can affect the resistance and reactance of the system's equivalent circuit.

Visit to know more about Voltage:-

brainly.com/question/30435728

#SPJ11

To calculate the electric field strength, we will use the formula for the energy stored in a capacitor:
Energy = (1/2) × C × E² × V, where Energy is the energy stored, C is the capacitance, E is the electric field strength, and V is the volume of the region.

Given:
Energy = 100 pJ (picojoules) = 100 × 10(-12) J,
V = 1.0 cm × 1.0 cm × 1.0 cm = (0.01 m)³.

Since we need to find the electric field strength (E), we can rewrite the formula as:
E² = (2 × Energy) / (C × V).

However, we don't have the capacitance (C) value. For a parallel plate capacitor, the formula for capacitance is:
C = ε₀ × A / d, where ε₀ is the vacuum permittivity (approximately 8.854 × 10 F/m), A is the area of the plates, and d is the distance between the plates.

In this case, we don't have enough information to calculate the capacitance (C) and subsequently the electric field strength (E). Please provide more information to help you further.

For more such questions on Electric field strength, visit:

brainly.com/question/15170044

#SPJ11

A rigid circular inclusion in a large plate subjected to pure shear at remote boundaries creates stress concentrations around the inclusion, which increase with decreasing shear modulus of the inclusion.

When a plate is subjected to pure shear stress, the stress distribution is uniform throughout the plate, except near the boundaries. However, the presence of a rigid circular inclusion within the plate creates stress concentrations around the inclusion due to the mismatch in stiffness between the inclusion and the surrounding matrix.

These stress concentrations increase with decreasing shear modulus of the inclusion. This phenomenon is important in understanding the behavior of composite materials, where the presence of inclusions of different materials affects the overall mechanical properties of the composite.

To know more about shear modulus, here

brainly.com/question/13261401

#SPJ4

--The complete question is, What is the effect of a rigid circular inclusion on the stress distribution of a large plate subjected to pure shear at remote boundaries? How does the value of the shear modulus of the inclusion affect the stress concentration around the inclusion?--

The ferry boat is sailing in a direction of 0 degrees (due North) at a speed of 10.39 km/h. To determine the direction of the ferry boat as observed from the shore, we must consider both the ferry boat's velocity and the river's velocity. The ferry boat is sailing at 12 km/h 30 degrees W of N, and the river is flowing at 6.0 km/h E.

Step 1: Break the ferry boat's velocity into its components:
- Northward component: 12 km/h * cos(30°) = 10.39 km/h
- Westward component: 12 km/h * sin(30°) = 6 km/h

Step 2: Add the river's velocity to the ferry boat's components:
- Northward component: 10.39 km/h (unchanged)
- Eastward component: 6.0 km/h (from the river) - 6 km/h (from ferry boat) = 0 km/h

Step 3: Determine the resultant velocity's magnitude and direction:
- Magnitude: √(10.39^2 + 0^2) = 10.39 km/h
- Direction: tan^-1(0/10.39) = 0° (N).

To know more about ferry boat refer here:

https://brainly.com/question/30583317#

#SPJ11

Induced emf in the loop is 8.4 x 10⁻⁵ A

power dissipated by the loop while the magnetic field is changing is 0.029 W

The induced emf in the loop can be calculated using Faraday's law, which states that the magnitude of the induced emf is proportional to the rate of change of magnetic flux through the loop. Since the loop is perpendicular to the magnetic field, the magnetic flux through the loop is given by the product of the magnetic field strength and the area of the loop. Therefore, the induced emf can be calculated as follows:
emf = -dΦ/dt = -(Bf - Bi)/t
where Bf is the final magnetic field strength, Bi is the initial magnetic field strength, and t is the time taken for the magnetic field to change. Substituting the given values, we get:
emf = -(0 - 1.4)/0.4 = 3.5 V
The power dissipated by the loop can be calculated using the formula P = I²R, where I is the current flowing through the loop and R is its resistance. Since the loop is a closed circuit, the induced emf will cause a current to flow through it. Using Ohm's law, we can calculate the current as follows:
I = emf/R = 3.5/41600 = 8.4 x 10⁻⁵ A
Substituting this value into the power formula, we get:
P = I²R = (8.4 x 10⁻⁵)² x 41600 = 0.029 W
Therefore, the power dissipated by the loop while the magnetic field is changing is very small, indicating that the heating of tissues under normal circumstances is also very small.

To learn more about induced emf https://brainly.com/question/13744192

#SPJ11

The energy is used to crush dried corn with a mortar and pestle is mechanical energy.

The advantage of using a mortar and pestle, is that the substance is crushed with little force, preventing it from warming up.

Traditional mortar and pestle grinding for carrying out mechanochemical reactions is subject to changeable influences, both human and environmental, despite its widespread use and simplicity of operation. The amount of manual force used, which unavoidably varies between people and over time, affects how a person grinds. The results obtained by using a mortar and pestle are frequently unpredictable because of these difficult-to-control variables.

To learn more about mechanical energy, click:

https://brainly.com/question/20030300

#SPJ1

The partial pressure of Ar in the mixture is 0.537 atm.

To find the partial pressure of Ar in a mixture of 10.0 g of Ne and 10.0 g Ar with a total pressure of 1.60 atm, you can use Dalton's Law of Partial Pressures.

Here are the steps:

1. Calculate the moles of each gas using their molar masses (Ne: 20.18 g/mol, Ar: 39.95 g/mol):
  Moles of Ne = 10.0 g / 20.18 g/mol = 0.495 moles
  Moles of Ar = 10.0 g / 39.95 g/mol = 0.250 moles

2. Calculate the mole fractions of each gas:
  Mole fraction of Ne = moles of Ne / (moles of Ne + moles of Ar) = 0.495 / (0.495 + 0.250) = 0.664
  Mole fraction of Ar = moles of Ar / (moles of Ne + moles of Ar) = 0.250 / (0.495 + 0.250) = 0.336

3. Use Dalton's Law to find the partial pressure of Ar:
  Partial pressure of Ar = mole fraction of Ar * total pressure = 0.336 * 1.60 atm = 0.537 atm

Learn more about pressure:

https://brainly.com/question/28012687

#SPJ11

It will take approximately 10.29 minutes to cut the initial carbon dioxide content down to half.

Let's first find the initial amount of carbon dioxide in the room:

Initial carbon dioxide content = 0.12% = 0.0012

Volume of the room = 4 x 7 x 3 = 84 cubic meters

Let's assume that the rate of the uniform mixture leaving the room is V m³/min, and let's find V using the principle of conservation of mass.

Mass of carbon dioxide in the room at any time = Mass of carbon dioxide that entered the room - Mass of carbon dioxide that left the room

The mass of carbon dioxide that entered the room per minute = (0.0012) x (7 m³/min) x (1 kg/m³) = 0.0084 kg/min

The mass of carbon dioxide that left the room per minute = (0.12/100) x (V kg/m³) x (4 x 7 x 3 m³/min) x (1 kg/m³) = 0.084V kg/min

Therefore, using the principle of conservation of mass,

0.0084 kg/min = 0.084V kg/min

V = 0.1 m³/min

This means that the uniform mixture is leaving the room at a rate of 0.1 m³/min.

Let t be the time in minutes required to cut the initial carbon dioxide content down to half.

The mass of carbon dioxide in the room after time t is:

Mass of carbon dioxide = 0.12/100 x 84 m³ x 1 kg/m³ - 0.0084 kg/min x t + 0.04/100 x 7 m³ x 1 kg/m³ x t

= 0.1008 - 0.0084t + 0.0028t

= 0.1008 - 0.0056t

To cut the initial carbon dioxide content down to half, the mass of carbon dioxide in the room should be 0.06/100 x 84 m³ x 1 kg/m³ = 0.0504 kg.

Therefore, we need to solve the equation:

0.0504 = 0.1008 - 0.0056t

0.0056t = 0.0504 - 0.1008

t = 10.29 minutes (rounded to two decimal places)

learn more about conservation of mass here:

https://brainly.com/question/19217922

#SPJ11

The impulse needed to increase the car's speed from 30 m/s to 35 m/s is 75,000 kgm/s. The correct answer is (b).

The impulse needed to increase the car's speed can be calculated using the following equation:

Impulse = (Final velocity - Initial velocity) x mass

Where the mass of the car is not given, so we cannot calculate the exact impulse.

However, we can determine the direction of the impulse based on the change in velocity. Since the car is increasing in speed, the impulse must be in the same direction as the motion of the car. Therefore, we can eliminate options (a) and (e) as they both suggest a negative impulse, which would oppose the motion of the car.

Now, we can calculate the magnitude of the impulse using the given options.

Using option (b):

Impulse = (35 m/s - 30 m/s) x mass

Impulse = 5 m/s x mass

Option (b) suggests that the impulse is 75,000 kgm/s.

Plugging this value into the equation above, we can solve for the mass of the car:

75,000 kgm/s = 5 m/s x mass

mass = 15,000 kg

Therefore, the impulse needed to alter the car's speed from 30 m/s to 35 m/s is obtained as 75,000 kgm/s.

Learn more about impulse here:

https://brainly.com/question/30466819

#SPJ1

The impulse needed to increase the car's speed from 30 m/s to 35 m/s is 75,000 kgm/s. The correct answer is (b).

The impulse needed to increase the car's speed can be calculated using the following equation:

Impulse = (Final velocity - Initial velocity) x mass

Where the mass of the car is not given, so we cannot calculate the exact impulse.

However, we can determine the direction of the impulse based on the change in velocity. Since the car is increasing in speed, the impulse must be in the same direction as the motion of the car. Therefore, we can eliminate options (a) and (e) as they both suggest a negative impulse, which would oppose the motion of the car.

Now, we can calculate the magnitude of the impulse using the given options.

Using option (b):

Impulse = (35 m/s - 30 m/s) x mass

Impulse = 5 m/s x mass

Option (b) suggests that the impulse is 75,000 kgm/s.

Plugging this value into the equation above, we can solve for the mass of the car:

75,000 kgm/s = 5 m/s x mass

mass = 15,000 kg

Therefore, the impulse needed to alter the car's speed from 30 m/s to 35 m/s is obtained as 75,000 kgm/s.

Learn more about impulse here:

https://brainly.com/question/30466819

#SPJ1

To determine the buoyant force on the crown, we can use the principle of buoyancy, which states that the buoyant force on an object immersed in a fluid is equal to the weight of the fluid displaced by the object.

First, we need to calculate the volume of the crown. We can use the fact that the density of gold is 19300 kg/m^3, and the weight of the crown is 7.84 N, to find the volume of the crown:

Density = Mass/Volume

Volume = Mass/Density

Volume = 7.84 N / (19300 kg/m^3)

Volume = 4.06 x 10^-4 m^3

Next, we need to determine the weight of the water displaced by the crown when it is submerged in water. We can use the fact that the weight of the crown in water is 6.84 N, to find the weight of the water displaced by the crown:

Weight of water displaced = Weight of crown - Weight of crown in water

Weight of water displaced = 7.84 N - 6.84 N

Weight of water displaced = 1 N

Since the density of water is 1000 kg/m^3, we can use the weight of the water displaced to find the volume of water displaced:

Density = Mass/Volume

Volume = Mass/Density

Volume = 1 N / (1000 kg/m^3)

Volume = 1 x 10^-3 m^3

Since the volume of water displaced is equal to the volume of the crown, we can conclude that the crown is made of pure gold, since its density is the same as that of gold.

Therefore, the buoyant force on the crown is equal to the weight of the water displaced, which is 1 N.

To know more about buoyant force :

https://brainly.com/question/21990136

#SPJ11

The tension in the elevator cable if the 1,000kg elevator is descending with an acceleration of 1.8 m/s2, downward is 8,000 N. The correct option is b.

To find the tension in the elevator cable, we need to use the formula: Tension (T) = m(g - a), where m is the mass of the elevator (1,000 kg), g is the acceleration due to gravity (9.8 m/s²), and a is the acceleration of the descending elevator (1.8 m/s²).

T = 1,000 kg * (9.8 m/s² - 1.8 m/s²)
T = 1,000 kg * 8 m/s²
T = 8,000 N

Therefore, the tension in the elevator cable is 8,000 N (option b).

For more such questions on Tension.

https://brainly.com/question/18649440#

#SPJ11

We can use the equation Q = I * t, where Q is the charge that passes through the patient's body, I is the current, and t is the time for which the current flows.

Given that the defibrillator sends 12 A of current through the patient's body for 0.20 s, I is the current, and t is the time for which the current flows.  we can substitute these values into the equation: Q = I * t = 12 A * 0.20 s = 2.4 C Therefore, the amount of charge that passes through the patient's body is 2.4 C. a certain defibrillator sends 12 a of current through a patient's body in 0.20 s.   charge, in c, We can use the equation Q = I * t, where Q is the charge that passes through the patient's body,  passes through the patient's body

Learn more about   defibrillator  here:

https://brainly.com/question/30434883

#SPJ11

When a heavy bag falls off a moving cart on a horizontal track, the speed of the cart will be affected due to the conservation of linear momentum.

As the bag falls straight down, an equal and opposite impulse acts on the cart, causing it to increase in speed. In an impulse-momentum bar chart, the initial momentum (mass x initial velocity) of the cart-bag system is represented by a bar. After the bag falls, the final momentum is split into two separate bars: one for the cart and one for the bag. The cart's momentum bar will be larger than its initial momentum, indicating an increase in its speed, while the bag's momentum bar will represent its downward momentum. The sum of the final momentum bars will be equal to the initial momentum bar, conserving the total linear momentum of the system.

Learn more about momentum :

https://brainly.com/question/30677308

#SPJ11

When a heavy bag falls off a moving cart on a horizontal track, the speed of the cart will be affected due to the conservation of linear momentum.

As the bag falls straight down, an equal and opposite impulse acts on the cart, causing it to increase in speed. In an impulse-momentum bar chart, the initial momentum (mass x initial velocity) of the cart-bag system is represented by a bar. After the bag falls, the final momentum is split into two separate bars: one for the cart and one for the bag. The cart's momentum bar will be larger than its initial momentum, indicating an increase in its speed, while the bag's momentum bar will represent its downward momentum. The sum of the final momentum bars will be equal to the initial momentum bar, conserving the total linear momentum of the system.

Learn more about momentum :

https://brainly.com/question/30677308

#SPJ11

The resistance of the 0.2 mm diameter wire redrawn from a melted wire of 1.0 mm diameter is approximately 3125 mΩ.

To find the new resistance of the wire, we will first calculate the volume of the original wire and then find the new length using the given diameter. Lastly, we will apply the formula for resistance.

1. Volume of the original wire:
V = πr²h
V = π(0.5mm)²(2000mm) = 1570.8 mm³ (approx)

2. Find the new length (L₂):
V = πr²h
1570.8 = π(0.1mm)²(L₂)
L₂ = 50000 mm (50 m)

3. Calculate new resistance using the formula:
R = ρ(L/A)
Where ρ (rho) is the resistivity, L is the length, and A is the cross-sectional area.

First, find the resistivity (ρ) using the original resistance:
50 mΩ = ρ(2000mm) / (π(0.5mm)²)
ρ = 19.63 µΩm (approx)

Now, calculate the new resistance (R₂):
R₂ = 19.63 µΩm * (50000 mm) / (π(0.1mm)²)
R₂ ≈ 3125 mΩ (approx)

The new resistance of the 0.2 mm diameter wire is approximately 3125 mΩ.

Learn more about resistance here: https://brainly.com/question/28135236

#SPJ11

The resistance of the 0.2 mm diameter wire redrawn from a melted wire of 1.0 mm diameter is approximately 3125 mΩ.

To find the new resistance of the wire, we will first calculate the volume of the original wire and then find the new length using the given diameter. Lastly, we will apply the formula for resistance.

1. Volume of the original wire:
V = πr²h
V = π(0.5mm)²(2000mm) = 1570.8 mm³ (approx)

2. Find the new length (L₂):
V = πr²h
1570.8 = π(0.1mm)²(L₂)
L₂ = 50000 mm (50 m)

3. Calculate new resistance using the formula:
R = ρ(L/A)
Where ρ (rho) is the resistivity, L is the length, and A is the cross-sectional area.

First, find the resistivity (ρ) using the original resistance:
50 mΩ = ρ(2000mm) / (π(0.5mm)²)
ρ = 19.63 µΩm (approx)

Now, calculate the new resistance (R₂):
R₂ = 19.63 µΩm * (50000 mm) / (π(0.1mm)²)
R₂ ≈ 3125 mΩ (approx)

The new resistance of the 0.2 mm diameter wire is approximately 3125 mΩ.

Learn more about resistance here: https://brainly.com/question/28135236

#SPJ11

If the RMS voltage across the 1.86 kΩ resistor is 115 V then:

(a) The potential difference across the resistor is 162.6 V.

(b) The maximum current through the resistor is 0.087 A.

(c) The RMS current through the resistor is 0.062 A.

(d) The average power dissipated by the resistor is 7.13 W.

(a) The maximum potential difference across the resistor can be found using the formula Vmax = Vrms x √2, where Vrms is the RMS voltage.

Plugging in the values, we get Vmax = 115 x √2 = 162.6 V.

Therefore, the maximum potential difference across the resistor is 162.6 V.

(b) The maximum current through the resistor can be found using Ohm's Law, which states that I = V/R, where V is the potential difference and R is the resistance.

Plugging in the values, we get I = 162.6/1860 = 0.087 A.

Therefore, the maximum current through the resistor is 0.087 A.

(c) The RMS current through the resistor is equal to the maximum current divided by √2.

Therefore, Irms = 0.087/√2 = 0.062 A.

(d) The average power dissipated by the resistor can be found using the formula Pavg = Vrms x Irms x cos(θ), where cos(θ) is the power factor.

For a purely resistive circuit like this one, the power factor is 1.

Plugging in the values, we get Pavg = 115 x 0.062 x 1 = 7.13 W.

Therefore, the average power dissipated by the resistor is 7.13 W.

Learn more about RMS voltage:

https://brainly.com/question/31389253

#SPJ11

The color of light emitted from each vial is related to the size of the quantum dots within them because of the way that quantum dots interact with light.

Quantum dots are nanoscale particles made of semiconducting materials. When exposed to light, they absorb the light and then re-emit it at a different frequency, creating a colored glow.

The frequency of the light emitted is determined by the size of the quantum dot. Larger quantum dots emit light at longer wavelengths, which appear red, while smaller quantum dots emit light at shorter wavelengths, which appear blue or green.

Therefore, the color of the light emitted by a vial containing quantum dots indicates the size of the quantum dots within it. For example, a vial emitting red light contains larger quantum dots than a vial emitting blue or green light.

By using different sized quantum dots, researchers can create a range of colors and hues for various applications, such as in electronics, lighting, and medical imaging.

To know more about quantum dots, refer here:
https://brainly.com/question/14399698
#SPJ11

The color of light emitted from each vial is related to the size of the quantum dots within them because of the way that quantum dots interact with light.

Quantum dots are nanoscale particles made of semiconducting materials. When exposed to light, they absorb the light and then re-emit it at a different frequency, creating a colored glow.

The frequency of the light emitted is determined by the size of the quantum dot. Larger quantum dots emit light at longer wavelengths, which appear red, while smaller quantum dots emit light at shorter wavelengths, which appear blue or green.

Therefore, the color of the light emitted by a vial containing quantum dots indicates the size of the quantum dots within it. For example, a vial emitting red light contains larger quantum dots than a vial emitting blue or green light.

By using different sized quantum dots, researchers can create a range of colors and hues for various applications, such as in electronics, lighting, and medical imaging.

To know more about quantum dots, refer here:
https://brainly.com/question/14399698
#SPJ11

(a)  The angular velocity is 2.5 rad/s and angular acceleration is 1.5 rad/s²

(b) The total acceleration of the machine component at B is 360 mm/s² to the right.

(a) To find the angular velocity of the idler pulley, we can use the formula:

ω = v / r

where v is the velocity of point A and r is the radius of the pulley. Thus, we have:

ω = 300 mm/s / 120 mm = 2.5 rad/s

To find the angular acceleration of the pulley, we can use the formula:

α = a / r

where a is the acceleration of point A and r is the radius of the pulley. Thus, we have:

α = 180 mm/s² / 120 mm = 1.5 rad/s²

(b) To find the total acceleration of the machine component at B, we can use the formula:

aB = aA + α × r

where aA is the acceleration of point A and α is the angular acceleration of the pulley. We know that aA = 180 mm/s² to the right, and from part (a) we found that α = 1.5 rad/s². The radius of the pulley is 120 mm. Thus, we have:

aB = 180 mm/s² + (1.5 rad/s²) × 120 mm

aB = 360 mm/s² to the right

To know more about angular acceleration click on below link:

https://brainly.com/question/29428475#

#SPJ11

The intensity at the angular position of the second minimum is equal to the intensity at the center of the central maximum (I0).

Part A:

The angular position of the first-order, two-slit, interference maxima can be found using the formula:

sinθ = mλ/d

where θ is the angular position of the maxima, m is the order of the maxima (m=1 for first-order maxima), λ is the wavelength of light, and d is the distance between the centers of the two slits.

Plugging in the given values, we get:

sinθ = (1)(600 nm)/(0.490 mm) = 0.244

θ = [tex]sin^(-1)( 0.244) = 14.1°[/tex]

Therefore, the angular position of the first-order, two-slit, interference maxima is 14.1°.

Part B:

The angular position of the second-order, two-slit, interference maxima can be found using the same formula as in Part A, but with m=2:

[tex]sinθ = (2)(600 nm)/(0.490 mm) = 0.488\\θ = sin^(-1)(0.488) = 29.0°[/tex]

Therefore, the angular position of the second-order, two-slit, interference maxima is 29.0°.

Part C:

The intensity of the interference pattern at the angular position of the first minimum (not the first maximum) is given by:

[tex]I = I0(cos(πw sinθ/λ)[/tex][tex])^2[/tex]

where I0 is the intensity at the center of the central maximum, w is the width of the slit, λ is the wavelength of light, and θ is the angular position of the minimum.

For the first minimum, m=1 and sinθ = λ/w. Plugging in the given values, we get:

sinθ = λ/w = 600 nm/0.330 mm = 0.182

[tex]I = I0(cos(πw sinθ/λ))^2 = I0(cos(π/2))^2 = I0(0) = 0[/tex]

Therefore, the intensity at the angular position of the first minimum is zero.

Part D:

The intensity of the interference pattern at the angular position of the second minimum is also given by the same formula as in Part C, but with m=2:

[tex]I = I0(cos(2πw sinθ/λ))[/tex][tex]^2[/tex]

For the second minimum, sinθ = 2λ/w. Plugging in the given values, we get:

[tex]sinθ = 2λ/w = 2(600 nm)/0.330 mm = 0.364\\I = I0(cos(2πw sinθ/λ))^2 = I0(cos(2π))^2 = I0(1)^2 = I0[/tex]

learn more abouT  interference pattern   here:

https://brainly.com/question/30217637

#SPJ4

If the elements in two arrays are related by their subscripts, the arrays are called : d. parallel

A collection of parallel arrays, commonly referred to as a structure of arrays (SoA), is a type of implicit data structure used in computing to represent a single array of records using many arrays. Each field of the record is maintained as a distinct, homogenous data array with an equal amount of items.

In parallel arrays, a collection of data is represented by two or more arrays, where each corresponding array index represents a field that matches a particular record. The array items at names[2] and ages[2] would describe the name and age of the third individual, for instance, if there were two arrays, one for names and the other for ages. The elements in two arrays are related by their subscripts.

To know more about arrays visit https://brainly.com/question/30757831

#SPJ11

The amount of heat produced by the electric iron per hour is 2,012,256 J.

The amount of heat produced is determined by the current, voltage, or conductor resistance. The resistance is the most important factor in the design of heating elements.

The positive ions in the crystal vibrate more as the temperature rises, and more collisions occur between the valence electrons and the vibrating ions. These collisions obstruct the "drift" motion of the valence electrons, resulting in a decrease in current.

To find the amount of heat developed per hour by the electric iron, we can use the formula:

Heat = Power x time

We know that power is the product of voltage and current:

Power = voltage x current

Given,

The voltage of the electric iron = 137 V

Current = 4.08 A

we can calculate the power,

Power = 137 V x 4.08 A = 558.96 W

Now,

Heat = Power x time

We have to convert 1 hour into seconds,

1 hour = 3600 seconds

The heat developed per hour is:

Heat = 558.96 W x 3600 s = 2,012,256 J

To know more about the heat developed visit:

https://brainly.com/question/28566557

#SPJ1