A truck is pulling a car. . is the magnitude of the force that the truck exerts on the car ·FC is the magnitude of the force that the car exerts on the truck onsider the following scenarios independently he truck is coasting along with a constant velocity on a horizontal surface, neglecting friction Submit Answer Tries 0/2 he truck is speeding up while driving up a mountain, neglecting friction FTF ㄒㄧ Submit Answer Tries 0/2 he truck is driving with a constant velocity, but as it turns out, the driver of the car left the emergency brake on

The potential difference across all three resistors in a series circuit is the same, as the voltage from the battery is divided across the resistors in proportion to their resistance values. Therefore, option B (potential difference ΔV) is the same for all three resistors.

The resistance of each resistor is different, so option C is not the same for all three resistors.

The current through each resistor is the same, as there is only one path for the current to flow in a series circuit. Therefore, option A (current I) is the same for all three resistors.

So the correct answer is D, "A and B".

learn more abouT Potential difference  here:

https://brainly.com/question/24142403

#SPJ4

The braking distance of the car from the question is 60 m

The braking distance is the distance traveled by a vehicle after the brakes have been applied, until it comes to a complete stop. It is the sum of the thinking distance (the distance traveled by the vehicle while the driver reacts to a hazard and decides to apply the brakes) and the braking distance (the distance traveled by the vehicle while the brakes are being applied to slow it down).

Given that;

F = ma

a = F/m

a = 5000 N/1500 Kg

a = 3.33 m/s^2

Given that;

v^2 = u^2 - 2as

Since v = 0

u^2 = 2as

s = u^2/2a

s = (20)^2/2 * 3.33

s = 60 m

Learn more about distance:https://brainly.com/question/15172156

#SPJ1

The width of the central bright fringe on the screen is approximately 5.67 mm.

To calculate the width on the screen of the central bright fringe, we need to use the equation:
w = (λL)/d
Substituting the given values, we get:
w = (630 nm x 1.80 m)/0.400 mm
w = 2.835 x 10^-3 m or 2.84 mm (rounded to two significant figures)
Width = 2 * (λL / a)
- Width is the width of the central bright fringe on the screen
- λ is the wavelength of light (630 nm or 630 x 10^-9 m)
- L is the distance between the slit and the screen (1.80 m)
- a is the width of the slit (0.400 mm or 0.400 x 10^-3 m)
Width = 2 * (630 x 10^-9 m * 1.80 m) / (0.400 x 10^-3 m)
Width ≈ 0.00567 m or 5.67 mm

To know more about width visit :-

https://brainly.com/question/21566137

#SPJ11

Answer:

If A'B'C' is the image of ABC in the mirror, then the distance between the object (ABC) and its mirror is equal to the distance between A'B'C' and the mirror.

Let's call the distance between A'B'C' and the mirror "d". According to the problem, we know that:

d = 80 cm

However, we need to find the distance between ABC and its mirror, which we can call "x". We know that:

x + d = 2x

Simplifying this equation, we get:

d = x

Substituting the value of "d" from the first equation, we get:

x = 80 cm

Therefore, the distance between the object (ABC) and its mirror is also 80 cm, which is the same as the distance between A'B'C' and the mirror.

Explanation:

The answer is c. It will rotate clockwise. A current loop is placed in magnetic field as shown. If It is released from rest, it will rotate clockwise.

With a magnetic field that is homogenous, there is no net force acting on a current loop. With a magnetic field that weakens to the right, a current loop with a magnetic moment pointing left is present.

Every location along a circular loop carrying electricity has magnetic field lines that are concentric circles. The right-hand thumb rule may be used to determine the magnetic field direction of each segment of the circular loop.

To know more about current loop visit:-

https://brainly.com/question/15204409

#SPJ1

The answer is c. It will rotate clockwise. A current loop is placed in magnetic field as shown. If It is released from rest, it will rotate clockwise.

With a magnetic field that is homogenous, there is no net force acting on a current loop. With a magnetic field that weakens to the right, a current loop with a magnetic moment pointing left is present.

Every location along a circular loop carrying electricity has magnetic field lines that are concentric circles. The right-hand thumb rule may be used to determine the magnetic field direction of each segment of the circular loop.

To know more about current loop visit:-

https://brainly.com/question/15204409

#SPJ1

The magnitude of the magnetic flux through the ring is approximately 4.9×10[tex]−4[/tex] Wb (we rounded the answer to two significant figures).

The magnetic flux through a circular loop is given by:

Φ = BAcosθ

Where Φ is the magnetic flux, B is the magnetic field, A is the area of the loop, and θ is the angle between the magnetic field and the normal to the loop.

In this case, the magnetic field is 5.8×10[tex]-2[/tex] T, the radius of the loop is 5.3 cm (or 0.053 m), and the angle between the magnetic field and the normal is 16∘.

The area of a circle is given by:

A = πr^2

So the area of the loop is:

A = π(0.053 m)[tex]^2[/tex] ≈ 8.83×10₃

Substituting the values into the equation for magnetic flux, we get:

Φ =[tex](5.8×10−2 T)(8.83×10−3 m^2)cos(16∘) ≈ 4.9×10−4 Wb[/tex]

Therefore, the magnitude of the magnetic flux through the ring is approximately 4.9×1[tex]0−4 Wb[/tex] (we rounded the answer to two significant figures).

learn more about magnetic flux here:

https://brainly.com/question/14411049

#SPJ4

The radius of a 1.000-turn coil that carries a 66.000 A current and has a magnetic moment of 5.100 x 10⁻² Am² is approximately 1.568 x 10⁻² meters.

To find the radius of the coil, we will use the formula for the magnetic moment, which is given by:

Magnetic moment (μ) = N * I * A

where N is the number of turns (1.000 turn), I is the current (66.000 A), and A is the area of the coil.

We know the magnetic moment (μ) = 5.100 x 10⁻² Am², so we can solve for the area (A):

A = μ / (N * I) = (5.100 x 10⁻²) / (1.000 * 66.000) = 7.727 x 10⁻⁴ m²

Since the coil is circular, we can use the formula for the area of a circle:

A = π * r²

where r is the radius of the coil.

Now we can solve for the radius (r):

r² = A / π = (7.727 x 10⁻⁴) / π

r² ≈ 2.460 x 10⁻⁴

Taking the square root of both sides:

r ≈ √(2.460 x 10⁻⁴) ≈ 1.568 x 10⁻² m

So, the radius of the coil is approximately 1.568 x 10⁻² meters.

Learn more about magnetic moment here: https://brainly.com/question/27962324

#SPJ11

The portable DVD player requires 1.746 watts of power.

To calculate the power required by the portable DVD player, you can use the formula P = I x V, where P is power in watts, I is current in amperes, and V is voltage in volts.

Given that the player draws a current of 194 mA at 9.00 V, we need to convert the current to amperes by dividing it by 1000.

So, I = 194 mA / 1000 = 0.194 A

Using the formula P = I x V, we get:

P = 0.194 A x 9.00 V = 1.746 watts

Therefore, the portable DVD player requires 1.746 watts of power.

Learn More about DVD here :-

https://brainly.com/question/23896058

#SPJ11

The commonly expressed equation to describe Newton's second law of motion is F = m×a.

Newton's second law of motion states that the acceleration of an object is directly proportional to the force applied to it, and inversely proportional to its mass.

Mathematically, this can be expressed as F = ma, where F is the net force applied to an object, m is the object's mass, and a is the resulting acceleration of the object.

In other words, the greater the force applied to an object, the greater its acceleration will be, and the more massive the object is, the less its acceleration will be for a given force.

This law is one of the fundamental principles of classical mechanics and is essential for understanding the behavior of objects in motion.

To learn more about Newton's law visit: https://brainly.com/question/25545050

#SPJ11

the linear acceleration of a car, the 0.310-m radius tires of which have an angular acceleration of 15.5 rad/s2 is 4.805 m/s².

To calculate the linear acceleration of a car with 0.310-meter radius tires and an angular acceleration of 15.5 rad/s², you can use the following formula:

Linear acceleration (a) = Radius of tires (r) × Angular acceleration (α)

Step 1: Identify the given values
- Radius of tires (r) = 0.310 meters
- Angular acceleration (α) = 15.5 rad/s²

Step 2: Use the formula to calculate the linear acceleration
a = 0.310 m × 15.5 rad/s²

Step 3: Calculate the result
a = 4.805 m/s²

The linear acceleration of the car is 4.805 m/s².

Learn more about linear acceleration  at  brainly.com/question/13723307

#SPJ11

The work done on the particle by the force F is 20 J. Answer A is correct.

The work done on the particle by the force F can be calculated using the formula:

[tex]W = F \int ds[/tex]

where F is the force vector and ds is the displacement vector. Since the force is constant, we can simplify this to:

[tex]W = F . \int ds[/tex]

where [tex]\int ds[/tex] is the displacement vector. In this case, the particle moves 5m in the positive x direction, so we have:

[tex]\int ds = 5 \hat{i}[/tex]

Substituting this into the equation for work, we get:

W = F · 5 [tex]\hat{i}[/tex]

where F is the force vector given as:

F = (4 N) [tex]\hat{i}[/tex] + (2 N) [tex]\hat{j}[/tex] − (4 N) [tex]\hat{k}[/tex]

Taking the dot product of F and 5[tex]\hat{i}[/tex], we get:

[tex]F . 5 \hat{i} = (4 N) (5) + (2 N) (0) - (4 N) (0)\\\\ = 20 J[/tex]

Choice A is correct.

To know more about force, here

https://brainly.com/question/13191643

#SPJ1

The distance between the probes is given as  117.86 A

We are given that the fluorescence intensity of probe A decreases from 160 units in the absence of probe B to 156 units in the presence of probe B. This decrease in intensity is due to the energy transfer from probe A to probe B. The efficiency of energy transfer can be calculated using the following equation:

E = 1 - (I_AB / I_A)

where I_AB is the fluorescence intensity of probe A in the presence of probe B and I_A is the fluorescence intensity of probe A in the absence of probe B.

Substituting the given values, we get:

E = 1 - (156 / 160) = 0.025

Now we can calculate the distance between the probes:

R = 64 A * [(1/0.025) - 1]^(1/6) = 117.86 A

Therefore, the distance between the probes is approximately 117.86 A.

Read more on distance here:https://brainly.com/question/26046491

#SPJ1

The period of a mass oscillating according to the equation x(t)=0.21 cos(145t) is equal to the inverse of the frequency, which is equal to 145. This means that the mass completes one cycle of oscillation every 0.0069 seconds.

Therefore, the period of a mass with a mass of 0.75 kg oscillating according to this equation is equal to 1/145 seconds, or about 0.0069 seconds. This means that the mass oscillates at a frequency of 145 Hz, or cycles per second.

This means that the mass completes a full cycle of oscillation every 0.0069 seconds. Therefore, it takes the mass 0.0069 seconds to move from its maximum position to its minimum position and back again. This is the period of oscillation for the mass.

Know more about mass oscillating here

https://brainly.com/question/14510622#

#SPJ11

The red ball's final speed is 3 m/s.

The green ball's final speed is sqrt((20.50 m/s)^2 + (14.29 m/s)^2) = 25 m/s.

We can start by using conservation of momentum, which states that the total momentum of the system before the collision is equal to the total momentum of the system after the collision.

Let's first find the initial momentum of the system. The momentum of an object is given by its mass times its velocity.

Initial momentum = (mass of green ball) x (velocity of green ball) + (mass of red ball) x (velocity of red ball)

Initial momentum = (10 kg) x (25 m/s) + (15 kg) x (0 m/s) (since the red ball is not moving initially)

Initial momentum = 250 kg m/s

After the collision, the green ball is moving at a 35-degree angle to the left of its original direction. We can use trigonometry to find the x and y components of its velocity.

x component of velocity = (magnitude of velocity) x cos(angle)

x component of velocity = (25 m/s) x cos(35 degrees)

x component of velocity = 20.50 m/s

y component of velocity = (magnitude of velocity) x sin(angle)

y component of velocity = (25 m/s) x sin(35 degrees)

y component of velocity = 14.29 m/s

So the final velocity of the green ball can be represented as a vector (20.50 m/s, 14.29 m/s) at a 35-degree angle to the left of its original direction.

Now, let's find the final velocity of the red ball. We know that it is moving to the right at a 55-degree angle from the green ball's original direction. Again, we can use trigonometry to find the x and y components of its velocity.

x component of velocity = (magnitude of velocity) x cos(angle)

x component of velocity = (magnitude of velocity) x cos(55 degrees)

y component of velocity = (magnitude of velocity) x sin(angle)

y component of velocity = (magnitude of velocity) x sin(55 degrees)

We don't know the magnitude of the velocity, but we can use the conservation of momentum to find it. The final momentum of the system is also equal to 250 kg m/s (since there are no external forces acting on the system).

Final momentum = (mass of green ball) x (velocity of green ball) + (mass of red ball) x (velocity of red ball)

Final momentum = (10 kg) x (20.50 m/s) + (15 kg) x (magnitude of velocity)

Final momentum = 205 kg m/s + 15(magnitude of velocity)

250 kg m/s = 205 kg m/s + 15(magnitude of velocity)

45 kg m/s = 15(magnitude of velocity)

magnitude of velocity = 3 m/s

So the final velocity of the red ball can be represented as a vector (3 m/s, 2.69 m/s) at a 55-degree angle to the right of the green ball's original direction.

To summarize:

The red ball's final speed is 3 m/s.

The green ball's final speed is sqrt((20.50 m/s)^2 + (14.29 m/s)^2) = 25 m/s.

Learn more about momentum

.com/question/30487676

#SPJ11

1.62x10⁻⁴ J is  the potential energy of 3 charges, each with charge 3 millicoulombs by a distance of 1 meters.

To calculate the potential energy of 3 charges arranged in a line, we need to use the formula for electric potential energy by Coulombs law
PE = k×q1×q2/d
where k is Coulomb's constant, q1 and q2 are the charges, and d is the distance between them.
In this case, we have 3 charges of 3 millicoulombs each arranged in a line, separated by a distance of 1 meter. Let's label them as q1, q2, and q3.
The potential energy of q1 and q2 is:
PE1-2 = k×q1×q2/d = (9x10⁹ N×m²/C²)×(3x10⁻³ C)×(3x10⁻³ C)/(1 m) = 8.1x10⁻⁵ J
The potential energy of q2 and q3 is:
PE2-3 = k×q2×q3/d = (9x10⁹ N×m²/C²)×(3x10⁻³ C)*(3x10⁻³ C)/(1 m) = 8.1x10⁻⁵ J
To find the total potential energy of the system, we just need to add the two values:
PE total = PE1-2 + PE2-3 = 2*(8.1x10⁻⁵ J) = 1.62x10⁻⁴ J
Therefore, the potential energy of 3 charges, each with charge 3 millicoulombs, arranged in a line and separated from each other by a distance of 1 meter, is 1.62x10⁻⁴ J.

Learn more about Coulombs law here

https://brainly.com/question/28040775

#SPJ11

tThe percent difference in resistance over this temperature range is 2.82% when coefficient of resistivity for carbon is -0.500 × 10⁻³/°C.

To determine the percent difference in resistance over this range, we need to use the given temperature coefficient of resistivity for carbon, which is -0.500 × 10⁻³/°C. First, we need to find the change in resistance:
ΔR = R × α × ΔT
Where ΔR is the change in resistance, R is the initial resistance, α is the temperature coefficient of resistivity, and ΔT is the change in temperature.
In this case, ΔT = 56.4°C, and α = -0.500 × 10⁻³/°C. We can't find the exact change in resistance without the initial resistance value, but we can still find the percent difference in resistance:
Percent difference = (ΔR / R) × 100
Plugging in the given values:
Percent difference = (R × (-0.500 × 10⁻³/°C) × 56.4°C) / R × 100
The R values cancel out, leaving:
Percent difference = (-0.500 × 10⁻³/°C × 56.4°C) × 100 = -2.82%
The negative sign indicates a decrease in resistance, so the percent difference in resistance over this temperature range is 2.82%.

Learn more about resistivity :

https://brainly.com/question/30799966

#SPJ11

Answer:

In other words, science is one of the most important channels of knowledge. It has a specific role, as well as a variety of functions for the benefit of our society: creating new knowledge, improving education, and increasing the quality of our lives. Science must respond to societal needs and global challenges.

The correct expression for the entropy change of the environment and the gas during an isobaric compression is:

b. ΔS_env + ΔS_gas > 0

During an isobaric compression, the gas is compressed at constant pressure. The reasoning behind this choice is as follows: In an isobaric process, the pressure remains constant throughout the compression. When an ideal gas undergoes compression, its volume decreases, and consequently, its entropy (ΔS_gas) also decreases, resulting in a negative value for ΔS_gas. However, the second law of thermodynamics states that the total entropy of a closed system, including the environment (ΔS_env), must always increase or remain constant. During the compression process, heat is transferred from the gas to the environment, which in turn increases the entropy of the environment (ΔS_env). Therefore, the sum of the entropy changes for both the gas and the environment (ΔS_env + ΔS_gas) must be greater than 0 to satisfy the second law of thermodynamics.

To learn more about  isobaric compression click here

https://brainly.com/question/13369842

#SPJ11

Air enters a nozzle steadily at 2.21 kg/m³ and 40 m/s and leaves at 0.762 kg/m³and 180 m/s. If the inlet area of the nozzle is 90 cm²,

(a) the mass flow rate through the nozzle is 0.7986 kg/s

(b) the exit area of the nozzle is 0.00582 m².

(a) To determine the mass flow rate through the nozzle,

we need to multiply the density of the air at the inlet (2.21 kg/m³) by the velocity of the air at the inlet (40 m/s) and the inlet area (90 cm²).

First, let's convert the inlet area from cm² to m²:

90 cm² = 90 * 0.0001 m²

            = 0.009 m²

Now we can calculate the mass flow rate:

          [tex]Mass flow rate = density * velocity * area[/tex]
           Mass flow rate = 2.21 kg/m^3 × 40 m/s × 0.009 m^2
           Mass flow rate = 0.7986 kg/s

So, the mass flow rate through the nozzle is 0.7986 kg/s.

(b) To find the exit area of the nozzle, we can use the mass flow rate and the exit conditions (density and velocity) provided.

First, we can rearrange the mass flow rate equation to solve for the exit area:

        [tex]Exit area = mass flow rate / (exit density * exit velocity)[/tex]

Now, plug in the given values:

Exit area = 0.7986 kg/s / (0.762 kg/m^3 × 180 m/s)
Exit area = 0.7986 kg/s / 137.16 kg/(m^2 s)
Exit area ≈ 0.00582 m^2

The exit area of the nozzle is approximately 0.00582 m^2.

Learn more about mass flow rate here:

https://brainly.com/question/15088427

#SPJ11

The overall voltage gain of the emitter follower when driven by a 30-k ohm source and loaded by a 1-k ohm resistor is approximately 0.00645 or 0.645%.

To find the overall voltage gain of the emitter follower, we need to first calculate its voltage gain under the given conditions.

The voltage gain of an emitter follower is approximately unity (i.e. 1) as the output voltage follows the input voltage with a small voltage drop across the transistor. Therefore, the voltage gain of the emitter follower is independent of the input signal frequency and is close to unity for all input frequencies.

Now, to calculate the output voltage of the emitter follower when driven by a 30-k ohm source and loaded by a 1-k ohm resistor, we need to use the voltage divider rule.
The output voltage can be calculated as:

Vout = Vin * (Rout / (Rout + Rin + Rload))

Where Vin is the input voltage, Rin is the input resistance (which is equal to the source resistance), and Rload is the load resistance.
Using the given values, we get:

Vout = Vin * (200 / (200 + 30,000 + 1,000))
Vout = Vin * 0.00645

Therefore, the overall voltage gain is 0.00645 or 0.645%.

Learn more about voltage gain at https://brainly.com/question/15303426

#SPJ11

The constructive interference occurs at points A and D.

Constructive interference occurs when two waves superpose (combine) in such a way that their amplitudes add up, resulting in a wave with a higher amplitude. In the case of two speakers operating in phase, where their wave patterns are aligned, constructive interference will occur at specific points where the crests of the waves align.

These points of constructive interference can be determined by examining the distance between the two speakers and the wavelength of the waves they produce. Constructive interference occurs when the path length difference between the two waves is an integer multiple of the wavelength.

Learn more about constructive interference, here:

https://brainly.com/question/31857527

#SPJ12

Your question is incomplete, most probably the full question is this:

two speakers, s1 and s2, operating in phase in the same medium produce the circular wave patterns shown in the diagram below. at which two points is constructive interference occurring?

After 6,451 years, there would be approximately 124.05 grams of carbon 14 left,  the time elapsed since the start of the half-life (in this case, 736 years), T is the half-life (5,715 years), and q0 is the initial mass (492 grams.

calculated as follows:

First, we need to determine how many half-lives have passed during the 6,451 years. To do this, we divide the time elapsed by the half-life:

6,451 years / 5,715 years per half-life = 1.13 half-lives

This means that 1 half-life has fully elapsed, and we're partway through the second half-life.

To calculate how much carbon 14 is left after 1 half-life, we use the formula:

q = q0 / 2

where q is the amount of carbon 14 remaining and q0 is the initial mass. In this case, q0 = 492 grams, so after 1 half-life (5,715 years), we have:

q = 492 / 2 = 246 grams

Now we need to calculate how much further decay occurs during the remaining 1/13th of a half-life. To do this, we use the formula:

q = q0 * (1/2)^(t/T)

where t is the time elapsed since the start of the half-life (in this case, 736 years), T is the half-life (5,715 years), and q0 is the initial mass (492 grams). Plugging in these values, we get:

q = 492 * (1/2)^(736/5,715) = 124.05 grams

Therefore, after 6,451 years, approximately 124.05 grams of carbon 14 would remain, assuming an initial mass of 492 grams.

Learn more about carbon here:

https://brainly.com/question/22530423

#SPJ11

The value of k, we can write the general formula:
T^2 = (9/16) * (a^3 / d^2)

To write a general formula describing the variation, we can use the given information:

The square of T varies directly with the cube of a and inversely with the square of d. We can express this relationship as:

T^2 = k * (a^3 / d^2)

Here, k is the constant of variation. Now, we'll use the given values of T, a, and d to find the value of k:

3^2 = k * (4^3 / 2^2)
9 = k * (64 / 4)
9 = k * 16
k = 9 / 16

Now that we've found the value of k, we can write the general formula:

T^2 = (9/16) * (a^3 / d^2)

To learn more about cube, refer below:

https://brainly.com/question/30962206

#SPJ11

The current through the coil is 13.91mA.

Current of 12a is carried through a circular coil with 250 turns and an 18 cm diameter. How Strong a Magnetic Moment Is There When the Coil Is Connected? -- Physics. Current carrying capacity is 12A in a circle with 250 turns and an 18 cm diameter.

The magnetic field at a location on the axis of a circular current-carrying coil with a 10 cm radius is 55 times greater than the magnetic field at the coil's centre.

M=I[tex]\pi r^{2}[/tex]

0.065=I3.14*9.8*9.8*7

I=13.91mA

To know more about magnetic moment visit:-

https://brainly.com/question/14446899

#SPJ1

When a 45 V potential difference is applied across a 1.8 kΩ resistor, a current flows through the resistor, following Ohm's law (I = V/R). Therefore, the current can be calculated by dividing the voltage by the resistance: I = 45 V / 1.8 kΩ = 0.025 A. This means that a current of 0.025 A, or 25 milliamperes (mA), flows through the resistor.

The flow of current through the resistor can cause various effects, depending on the circuit design and the properties of the resistor itself. For example, the resistor may generate heat as a result of the current flow, which can be a concern in some applications.

Additionally, the resistor can serve to limit the amount of current that flows through the circuit, which can help protect other components from damage due to overloading or short circuits.

Overall, understanding how current flows through resistors and other components is essential for designing and troubleshooting electrical circuits. By applying the principles of Ohm's law and other fundamental concepts, engineers, and technicians can ensure that circuits operate safely and effectively.

To know more about Ohm's law refer here:

https://brainly.com/question/1247379#

#SPJ11

We also know from Kepler's Second Law that the rate at which area is swept out by the radius vector is constant, which means dA/dt is constant. Therefore, we can deduce that 1/2 h is constant.

What is Velocity?

Velocity is a vector quantity that describes the rate of change of displacement of an object with respect to time. It is defined as the change in displacement per unit of time and includes both magnitude (speed) and direction. Velocity is typically denoted by the symbol "v" and is measured in units of distance per time, such as meters per second (m/s) or kilometers per hour (km/h).

d(theta)/dt = h/[tex]r^{2}[/tex]

Now, recall that the area A swept out by the radius vector r in a time interval dt is given by:

dA = (1/2)[tex]r^{2}[/tex] d(theta)

Taking the derivative of both sides with respect to time t, we get:

dA/dt = (1/2)[tex]r^{2}[/tex]d(theta)/dt

Substituting the expression for d(theta)/dt from above, we get:

dA/dt = (1/2)[tex]r^{2}[/tex] (h/[tex]r^{2}[/tex])

Simplifying, we get:

dA/dt = 1/2 h

Learn more about Velocity from the given link

https://brainly.com/question/24445340

#SPJ1

Yes I agree and the socio historical concept implies that race is created and maintained through systems of power and inequality.

According to Michael Omi and Howard Winant, in Racial Formations, race is a socio-historical concept that is constructed through the intersection of cultural, political, and economic forces.

In this book, they argue that race is not an immutable, biologically determined characteristic of individuals or groups but rather a social construct that is created and maintained through systems of power and inequality. The authors illustrate how race is constructed through examples from different historical periods and social contexts.

Learn more about race here: https://brainly.com/question/28138343

#SPJ1

The final velocity right after a 115 kg rugby player collides head‑on with a padded goalpost is approximately 0.61 m/s backwards.

To calculate the final velocity of the rugby player after the collision, we need to use the impulse-momentum theorem. The equation for this is:

Impulse = Change in momentum

Impulse = Force × Time
Change in momentum = Mass × Change in velocity

Given values:
Initial velocity (v₁) = 7.95 m/s
Mass (m) = 115 kg
Force (F) = -17900 N (backward force)
Time (t) = 5.50 × 10⁻² s

First, we'll find the impulse:
Impulse = Force × Time
Impulse = -17900 N × 5.50 × 10⁻² s
Impulse ≈ -984.5 kg·m/s

Now, we'll find the change in momentum:
Change in momentum = Impulse
Change in momentum = -984.5 kg·m/s

Next, we'll calculate the change in velocity:
Change in velocity = Change in momentum / Mass
Change in velocity ≈ -984.5 kg·m/s / 115 kg
Change in velocity ≈ -8.56 m/s

Finally, we'll find the final velocity (v₂):
v₂ = Initial velocity + Change in velocity
v₂ = 7.95 m/s - 8.56 m/s
v₂ ≈ -0.61 m/s

So, the final velocity of the rugby player right after the collision is approximately -0.61 m/s (negative sign indicates the backward direction).

Learn more about impulse-momentum theorem here: https://brainly.com/question/29787331

#SPJ11

a). Impedance of the circuit Incorrect:  Z = 85.9 ohms

(b) Rms current in the circuit: 0.69 A

c) Average power delivered to the circuit: 35.88 W

Due to the fact that DC current is a sort of continuous current, its frequency is 0 hertz. Therefore, AC current is not limited to zero Hz as its rest frequency.

Given : 85 sin(260t)

C = 28mF = 28x 10⁻³ F

Inductance = L = 0.250 H

a) Inductive reactance = X(L) = ω L = (350)(0.2) = 70 ohms

Capacitive reactance = X(C) = 1 / ωC = 0.114 ohms

Reactance = Z = [tex]\sqrt{R^{2} + (X_{L} - X_{C} ) }[/tex]

                  =  [tex]\sqrt{52^{2} +(70 -0.114)^{2} }[/tex]

                  =85.9

B )  current = I = 85 / 85.9 = 0.98 A

Irms = 0.98 / [tex]\sqrt{2}[/tex] = 0.69 A

c) P =  R = (0.69)(52) = 35.88 W

To know more about AC voltage visit:-

https://brainly.com/question/3792887

#SPJ1

Yes, it is possible for an application to run slower when assigned 10 processors compared to when it is assigned 8 processors.

This is because the application may not be optimized to effectively use all 10 processors, leading to increased overhead and decreased performance. Additionally, if the system is not able to effectively manage the workload distribution across all 10 processors, it can lead to congestion and decreased performance. Therefore, it is important to consider the specific requirements of the application and the capabilities of the system before assigning a specific number of processors.
This can happen due to factors such as poor parallelization, overhead, and diminishing returns. To optimize the application's performance, it is crucial to ensure efficient use of the available processors and manage parallel tasks effectively.

Learn more about processors: https://brainly.com/question/614196

#SPJ11