An air-standard Diesel cycle engine operates as follows: The temperatures at the beginning and end of the compression stroke are 30 °C and 700 °C, respectively. The net work per cycle is 590.1 kJ/kg, and the heat transfer input per cycle is 925 kJ/kg. Determine the a) compression ratio, b) maximum temperature of the cycle, and c) the cutoff ratio, v3/v2.

This question is incomplete, the complete question is;

An air-standard Diesel cycle engine operates as follows: The temperatures at the beginning and end of the compression stroke are 30 °C and 700 °C, respectively. The net work per cycle is 590.1 kJ/kg, and the heat transfer input per cycle is 925 kJ/kg. Determine the a) compression ratio, b) maximum temperature of the cycle, and c) the cutoff ratio, v3/v2.

Use the cold air standard assumptions.

Answer:

a) The compression ratio is 18.48

b) The maximum temperature of the cycle is 1893.4 K

c) The cutoff ratio, v₃/v₂ is 1.946

Explanation:

Given the data in the question;

Temperature at the start of a compression T₁ = 30°C = (30 + 273) = 303 K

Temperature at the end of a compression T₂ = 700°C = (700 + 273) = 973 K

Net work per cycle [tex]W_{net[/tex] = 590.1 kJ/kg

Heat transfer input per cycle Qs = 925 kJ/kg

a) compression ratio;

As illustrated in the diagram below, 1 - 2 is adiabatic compression;

so,

Tγ[tex]^{Y-1[/tex] = constant { For Air, γ = 1.4 }

hence;

⇒ V₁ / V₂ = [tex]([/tex] T₂ / T₁ [tex])^{\frac{1}{Y-1}[/tex]

so we substitute

⇒ V₁ / V₂ = [tex]([/tex]  973 K / 303 K  [tex])^{\frac{1}{1.4-1}[/tex]

= [tex]([/tex]  3.21122  [tex])^{\frac{1}{0.4}[/tex]

= 18.4788 ≈ 18.48

Therefore, The compression ratio is 18.48

b) maximum temperature of the cycle

We know that for Air, Cp = 1.005 kJ/kgK

Now,

Heat transfer input per cycle Qs = Cp( T₃ - T₂ )

we substitute

925 = 1.005( T₃ - 700 )

( T₃ - 700 ) = 925 / 1.005

( T₃ - 700 ) = 920.398

T₃ = 920.398 + 700

T₃ = 1620.398 °C

T₃ = ( 1620.398 + 273 ) K

T₃ = 1893.396 K ≈ 1893.4 K

Therefore, The maximum temperature of the cycle is 1893.4 K

c)  the cutoff ratio, v₃/v₂;

Since pressure is constant, V ∝ T

So,

cutoff ratio S = v₃ / v₂  = T₃ / T₂

we substitute

cutoff ratio S = 1893.396 K / 973 K

cutoff ratio S = 1.9459 ≈ 1.946

Therefore, the cutoff ratio, v₃/v₂ is 1.946

how do you know when an equation is (In)​

Assuming you determine the required section modulus of a wide flange beam is 200 in3, determine the lightest beam possible that will satisfy this condition.

The output side of an ideal transformer has 35 turns, and supplies 2.0 A to a 24-W device. Ifthe input is a standard wall outlet, calculate the number of turns on the input side, and the currentdrawn from the outlet.

Please send the solution quickly​

1. A hydro facility operates with an elevation difference of 50 m and a flow rate of 500 m3/s. If the rotational speed is 90 RPM, find the most suitable type of turbine and estimate the power output of the arrangement

How do Machine Learning and Artificial Intelligence (AI) technologies help businesses use their enterprise data effectively?

dentify the recommended practices when putting a tip on a micropipette. Select one or more: Gently push the micropipette into the tip and tap lightly to load the tip. Hold the micropipette at a 45 degree angle to the tip rack. Use the tip size designed for the micropipette size in use. Remove the tip from the rack and place it on micropipette by hand.

Which of the following are major components of a Class II BSC: A. Cabinet blower switch B. Foot support C. Drain spillage trough (catch basin) D. Rear grille E. Temperature control

Case Study # 1: Cadbury Crisis Management (Worm Controversy)

In India chocolate consumption was very low in the early 90’s but as the decade advanced the consumption drastically increased. The late 90’s witnessed a good chocolate market condition. The chocolate market in India is dominated by two multinational companies – Cadbury and Nestle. The national companies – Amul and Campco are other candidates in this race. Cadbury holds more than 70% of the total share of the market. Nestle has emerged by holding almost 20% of the total share. Apart from chocolate segment, there is also a big confectionery segment which is flooded by companies like Parry’s, Ravalgaon, Candico and Nutrine. All these are leading national players. The multinational companies like the Cadbury, Nestle and Perfetti are the new entrants in the sugar confectionery market. (Management paradise) There are several others which have a minor share in these two segments. According to statistics, the chocolate consumption in India is extremely low. If per capita consumption is considered, it comes to only 160gms in the urban areas. This amount is very low compared to the developed countries where the per capita consumption is more than 8-10kg. Observing this fact it would not be appropriate to consider the rural areas of India as it will be extremely low. This low consumption is owing to the notion behind consuming chocolates. Indians eat chocolates as indulgence and not as snack food. The major target population is the children. India has witnessed a slow growth rate of about 10% pa from the 70’s to the 80’s. But as the century advanced the market stagnated. This was the time when Cadbury launched its product- Dairy Milk as an anytime product rather than an occasional luxury. All the advertisements of Dairy Milk paid a full attention to adults and not children. And this proved to be the major breakthrough for Cadbury as it tried to break the conventional ideas of the Indians about chocolate.

The Worm Controversy
On October 2003, just a month before Diwali, the Food and Drug Administration Commissioner received complaints about infestation in two bars of Cadbury Dairy Milk, Cadbury India’s flagship brand with over 70% market share. He ordered an enquiry and went directly to the media with a statement. Over the following 3-week period, resultant adverse media coverage touched close to 1000 clips in print and 120 on TV news channels. In India, where Cadbury is synonymous with chocolate, the company’s reputation and credibility was under intense scrutiny. Sales volumes came down drastically in the first 10 weeks, which was the festival season; retailer stocking and display dropped, employee morale – especially that of the sales team – was shaken.

The challenge was to restore confidence in the key stakeholders (consumers, trade and employees, particularly the sales team) and build back credibility for the corporate brand through the same channels (the media) that had questioned it. In defense, Cadbury issued a statement that the infestation was not possible at the manufacturing stage and poor storage at the retailers was the most likely cause of the reported case of worms. But the FDA didn’t buy that. FDA commissioner, Uttam Khobragade told CNBC-TV18, “It was presumed that worms got into it at the storage level, but then what about the packing – packaging was not proper or airtight, either ways it’s a manufacturing defect with unhygienic conditions or improper packaging.” That was followed by allegations and counter-allegations between Cadbury and FDA. The heat of negative publicity melted Cadbury’s sales by 30 per cent, at a time when it sees a festive spike of 15 per cent. For the first time, Cadbury’s advertising went off air for a month and a half after Diwali, following the controversy. Consumers seemed to ignore their chocolate cravings.

Question:

1. How will the Cadbury can restore the confidence of the consumer?
Make an elaborate plan on how you are going to do it. Use the Decision-making Process. a) Diagnose problem
b) Analyze environment
c) Articulate problem or opportunity d) Develop viable alternatives
e) Evaluate alternatives f) Make a choice
g) Implement decision
h) Evaluate and adapt decision results

how are hybrid and gasoline cars alike

QUESTION 1
Outcome: Direct Current Motors.
1.1 Identify the parts of the direct current motor below.
​

1. Using the formula above, complete this task.

Concrete is currently sold in increments of 12 yd'. Concrete current cost is $45 per V2 yd. How much would it cost a Shameka's Construction Company to cement a pad size 18ft x 20 ft. floor, 4 inches thick?​

The term variation describes the degree to which an object or idea differs from others of the same type or from a standard.

a. True
b. False

what happen to the clutch system when you step-on and releasing the clutch pedal?​

6.D1 A large tower is to be supported by a series of steel wires. It is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter assuming a factor of safety of 2 and a yield strength of 860 MPa (125,000 psi).