calculate the magnetic force on an airplane which has acquired a net charge of 1540 μc and moves with a speed of 100 m/s perpendicular to the earth's magnetic field of 5.0×10−5t .

Single phase transformers are used to step up or step down the voltage of an AC power supply. They have two windings, the primary and the secondary, which are wound around a magnetic core. When an AC voltage is applied to the primary winding, it creates a magnetic field which induces a voltage in the secondary winding.

The three such transformers, each with a capacity of 400MVA. This means that each transformer can handle up to 400 megavolt-amperes of power. The voltage rating of these transformers is 13.8kV, which is the maximum voltage that they can handle.
Single-phase transformers are electrical devices that transfer energy between circuits while maintaining a constant frequency. They operate on single-phase AC power, which means the voltage and current waveforms are sinusoidal and have the same frequency. Each transformer has a power rating of 400 MVA (Mega Volt-Ampere). This value represents the maximum amount of apparent power that the transformer can handle without exceeding its thermal limits.
Additionally, the transformers are rated at 13.8 kV (kilo Volts) on one of their windings, either primary or secondary, depending on the desired voltage transformation.

Learn more about transformer here: brainly.com/question/31036096

#SPJ11

Average power equals the amount of power averaged over time. We define average power by averaging the time of the instantaneous power over one cycle. An object should be converted to energy before being moved. The use of force is one way to transfer energy. The amount of energy used by a force to move an item is referred to as the work done.

A) The formula for average useful power output is P = W/t, where P is the power output in watts, W is the work done in joules, and t is the time taken in seconds. First, convert the time taken from hours to seconds:
9.25 h x 60 min/h x 60 s/min = 33,300 s

Now we can put in the values:
P = (0.85 x 10^6 J) / (33,300 s)
P = 25.5 W

Therefore, the average useful power output of the person is 25.5 watts.

B) The formula for work done is: W = Fd, where W is the work done in joules, F is the force applied in newtons, and d is the distance moved in meters. We can rearrange this formula to solve for force:
F = W/d

To lift 2250 kg of bricks 1.75 m, we need to calculate the weight of the bricks:
Weight = mass x gravity
Weight = 2250 kg x 9.81 m/s^2
Weight = 22,107.5 N

Now we can calculate the force required to lift the bricks:
F = 22,107.5 N / 1.75 m
F = 12,632 N

Finally, we can calculate the time taken using the formula for power:
P = W/t
t = W/P

First, we need to calculate the work done:
W = Fd
W = (12,632 N) x (1.75 m)
W = 22,079 J

Now we can put in the values:
t = (22,079 J) / (25.5 W)
t = 865 s

Therefore, it will take this person 865 seconds (or 14.4 minutes) to lift the bricks to the platform.

Know more about work done:

https://brainly.com/question/28356414

#SPJ11

The force exerted on the spring by the student can be calculated using the formula:F = ma where F is the force, m is the mass of the student, and a is the acceleration of the elevator.

Substituting the given values, we get: F = (64 kg) × (3.3 m/s^2) = 211.2 N The spring exerts an equal and opposite force on the student, which can be calculated using Hooke's law: F = kx where F is the force exerted by the spring, k is the spring constant, and x is the displacement of the spring from its equilibrium position. Solving for x, we get x = F/k Substituting the given values, we get: x = (211.2 N) / (2800 N/m) = 0.0756 m Therefore, the spring is compressed by approximately 7.6 cm.

Learn more about   spring  here:

https://brainly.com/question/14670501

#SPJ11

The rotational kinetic energy of the object having a moment of inertia of 21 kg.m² and angular speed of 122 radians/s is 156,282 Joules.

To find the rotational kinetic energy of an object, you can use the following formula:

Rotational Kinetic Energy (K) = 0.5 × Moment of Inertia (I) × Angular Speed² (ω²)

In this case, the moment of inertia (I) is 21 kg·m² and the angular speed (ω) is 122 radians/s. Plugging these values into the formula, we get:

K = 0.5 × 21 kg·m² × (122 radians/s)²

Now, let's calculate the rotational kinetic energy:

K = 0.5 × 21 kg·m² × 14884 (radians/s)²
K = 10.5 kg·m² × 14884 (radians/s)²
K = 156,282 kg·m²/s²

Therefore, the rotational kinetic energy of the object is 156,282 Joules.

Learn more about the moment of inertia:

https://brainly.com/question/14119750

#SPJ11

The negative sign indicates that the direction of the momentum has reversed due to the collision with the wall. Therefore, the change in momentum of the soccer ball is 5 kg m/s in the opposite direction of its initial velocity.

The change in momentum of an object is equal to the final momentum minus the initial momentum.

The momentum (p) of an object is given by the product of its mass (m) and velocity (v):

p = mv

Initially, the soccer ball has a momentum of:

[tex]p_1 = m_1v_1 =[/tex] (0.5 kg)(12 m/s) = 6 kg m/s

After rebounding off the wall, the soccer ball has a velocity of 2 m/s. Therefore, the final momentum is:

[tex]p_1 = m_1v_1 =[/tex] (0.5 kg)(2 m/s) = 1 kg m/s

The change in momentum is then:

Δp =[tex]p_1 = m_1v_1 =[/tex]= 1 kg m/s - 6 kg m/s = -5 kg m/s

Learn more about momentum visit: brainly.com/question/18798405

#SPJ4

The width of the slit (3.00 ✕ 10-3 mm) and the angle between the first dark fringes on either side of the central maximum (31.0°) can be used to determine the wavelength of the monochromatic light.

The distance between the central maximum and the first dark fringe on either side (known as the first-order fringe) can be calculated using the formula:

sin θ = λ / b

where θ is the angle between the central maximum and the first-order fringe, λ is the wavelength of the light, and b is the width of the slit.

Rearranging this formula, we get:

λ = b sin θ

Substituting the values given, we get:

λ = (3.00 ✕ 10-3 mm) × sin 31.0°

λ = 1.55 ✕ 10-6 m

Therefore, the wavelength of the monochromatic light used is 1.55 ✕ 10-6 m.

Learn more about maximum here:

https://brainly.com/question/30693656

#SPJ11

When you toss the apple lightly straight up above your head and catch it as it returns to your hand, the speed of the apple starts at zero when you release it from your hand, then it accelerates until it reaches the highest point, at which point the speed becomes zero again before it starts to decelerate as it falls back to your hand.

However, when you throw the apple straight up as hard as you can, the speed of the apple is faster when you release it from your hand, and it accelerates quickly as it rises. The height of the apple's flight is higher than the lighter toss, and the time of flight is longer.

The same thing about both tosses is that the apple reaches its highest point before it starts to fall back down to your hand. However, the difference is in the speed, height, and time of flight. In the harder toss, the apple travels faster, reaches a greater height, and takes longer to complete its flight.

Learn more about straight here:

https://brainly.com/question/27176450

#SPJ11

The formula for the volume of a sphere is V = 4/3 π r³, where V = volume and r = radius. The radius of a sphere is half its diameter.

The current radius of the Sun is approximately 696,000 km. If the radius were to extend nearly to Earth's orbit, which is approximately 149.6 million km, the new radius would be approximately 150,296,000 km.

Using the formula for the volume of a sphere (4/3πr^3), we can estimate the volume of the Sun at that time. Plugging in the new radius, we get:
V = 4/3π(150,296,000 km)^3
V ≈ 2.684 × 10^27 km^3

This means that the volume of the Sun would be significantly larger than it is now.
To estimate the average matter of the Sun at that time, we can use the current mass of the Sun, which is approximately 1.99 × 10^30 kg. Since the volume of the Sun would be much larger, we can assume that the matter would be spread out more thinly.

Using the formula for density (D = m/V), we can estimate the average matter of the Sun at that time:
D = 1.99 × 10^30 kg / 2.684 × 10^27 km^3
D ≈ 743 kg/km^3

So,  the average matter of the Sun at that time would be much less dense than it is now. However, it is important to note that this is just an estimation based on current knowledge and understanding of the Sun. The actual volume and matter of the Sun at the end of its life could vary.

Learn more about the volume of a sphere:

https://brainly.com/question/28228180

#SPJ11      

The reading on the scale would be 590 N. So the correct answer is (b) 590 N.

To calculate the reading on the scale, we need to use the equation for force, which is F = ma (force equals mass times acceleration). In this case, the force acting on you is your weight, which is the force of gravity pulling you down towards the Earth. Therefore, we can write:

Weight = mass x acceleration due to gravity

Weight = 50 kg x 9.8 m/s^2

Weight = 490 N

However, the elevator is also accelerating upwards, which means there is an additional force acting on you. We can calculate this force using the same equation, but using the elevator's acceleration instead:

Additional force = mass x elevator's acceleration

Additional force = 50 kg x 2 m/s^2

Additional force = 100 N

The total force acting on you is the sum of your weight and the additional force:

Total force = Weight + Additional force

Total force = 490 N + 100 N

Total force = 590 N

Therefore, the reading on the scale would be 590 N. Hence , option (b) is correct.

To know more about Scale refer here :

https://brainly.com/question/18559363

#SPJ11

A)  the rms current in this circuit is 45.6mA. B) To find the current for a frequency of 2.20 kHz, we can simply double the original current, as the frequency is doubled: rms = 2 × 45.6 mA = 91.2 mA C) rms = 91.2 mA

Part A:
To find the rms current, we can use the formula:

Irms = Vrms / Xc

where Vrms is the rms voltage and Xc is the capacitive reactance, which is given by:

Xc = 1 / (2πfC)

where f is the frequency and C is the capacitance.

Plugging in the values given, we get:

Xc = 1 / (2π × 1.10kHz × 0.400μF) = 361.7Ω

Irms = 16.5V / 361.7Ω = 45.6mA

So the rms current in this circuit is 45.6mA.

Part B:
If the frequency of the voltage is doubled, the capacitive reactance will decrease, and the current will increase. The new capacitive reactance is given by:

Xc' = 1 / (2π × 2.20kHz × 0.400μF) = 180.8Ω

The new rms current can be found using the same formula as before:

Irms' = Vrms / Xc' = 16.5V / 180.8Ω = 91.2mA

So the current has doubled (increased by a factor of 2) when the frequency is doubled.

Part C:
To calculate the current for a frequency of 2.20kHz, we can use the formula we used in Part B:

Xc' = 1 / (2π × 2.20kHz × 0.400μF) = 180.8Ω

Irms' = Vrms / Xc' = 16.5V / 180.8Ω = 91.2mA

So the rms current for a frequency of 2.20kHz is 91.2mA.

To learn more about capacitive reactance click here

brainly.com/question/12356566

#SPJ11

Since they would only travel 21.3 m before reaching the basin's outlet, particles of this size would not be entirely removed in the settling basin as described. the 1.4 specific gravity particle with the smallest diameter.

The velocity that is produced by accelerating and drag forces is the particle's terminal velocity. Most frequently, it refers to a particle's rate of freefall in still air while being pulled downward by gravity.

r = ((9/2) * (Vt * pw) / ((p - pw) * g)) (1/2)

Substituting the given values, we get:

r = ((9/2) * (2.07 × 10⁻⁶ m/s) * 998.2 kg/m³) / ((1.4 - 998.2) kg/m³ * 9.81 m/s²)) (1/2)

= 4.31 × 10⁻⁶ m

Converting the radius back to diameter, we get:

d = 2 * r = 8.62 × 10⁻⁶ m = 8.62 µm

To know more about gravity visit:-

https://brainly.com/question/31321801

#SPJ1

The change in internal energy of the system is 2.05×10² kJ.

To calculate the change in internal energy (ΔE), we need to use the first law of thermodynamics: ΔE = Q - W. Here, Q represents the heat absorbed by the system, and W represents the work done on the system. In this case, the work done on the system is 3.50×10² kcal, and the system releases 5.00×10² kJ of heat.

First, we need to convert the work done from kcal to kJ: 3.50×10² kcal × 4.184 kJ/kcal = 1.46×10³ kJ. Since the system releases heat, Q is negative: Q = -5.00×10² kJ. Now, we can find the change in internal energy: ΔE = Q - W = -5.00×10² kJ - (-1.46×10³ kJ) = 2.05×10² kJ.

To know more about internal energy click on below link:

https://brainly.com/question/14668303#

#SPJ11

Here are my observations after looking through the cardboard tube with different sized holes at one end:

• Colors appeared more vibrant and saturated. Bright colors seemed almost neon in intensity.

• Colors appeared more separated and distinct. Shades seemed more differentiated. Subtle gradients were exaggerated.

• Shadows and highlights within colors were emphasized. Details within colors became more visible.

• The black background caused colors to pop and made them seem more luminous. Colors glowed against the black.

• Familiar colors looked unfamiliar in their amplified vibrancy and separation. Muted colors became bold. Pastel colors were vivid.

• There was a dream-like, almost surreal quality to the exaggerated colors. A strange, unfamiliar palette emerged.

• Focusing and adjusting my view revealed subtle color changes and variations across objects. New color patterns emerged.

• Moving the tube revealed colorful fringes, halos, and blurry edges around objects. Colors seemed to slide across edges.

• The effect made me see colors in a more mindful, contemplative way. I noticed colors more consciously. Familiar colors became fascinating.

• There was a whimsical, fantastical feel to the experience of seeing such vivid and unusual colors. An imaginative, almost non-logical aspect emerged.

Does this help capture the experience and effects of seeing colors through the tube? Let me know if any additional details would be helpful. I can provide more observations and descriptions.

The focal length (f) of the magnifier needed to view the 2.60 mm long insect with an angular size of radians, , the required focal length for the magnifier is approximately 102.6 mm.

We can use the formula:

magnification = (image distance)/(object distance) = (1 + focal length)/(focal length)

where the magnification is given by the angular size of the image divided by the angular size of the object:

magnification = (angular size of image)/(angular size of object)

In this case, we want the angular size of the image to be 2.80×10−2 radians and the length of the object (the insect) is 2.60 mm. We can convert the length to meters (since the angular size is given in radians) by dividing by 1000:

object size = 2.60/1000 = 2.6×10−3 m

Now we can solve for the focal length:

magnification = (angular size of image)/(angular size of object) = (2.80×10−2)/(2.6×10−3) = 10.77

magnification = (1 + focal length)/(focal length)

10.77 = (1 + f)/(f)

10.77f = 1 + f

9.77f = 1

f = 0.1026 m = 102.6 mm

Therefore, the required focal length is 102.6 mm.

Learn more about focal here:'

https://brainly.com/question/16188698

#SPJ11

Move an object from the ground onto a stand without moving the vehicle, the boom operator should retract hydraulic  A and extend hydraulic cylinder.

A cylinder is a three-dimensional geometric shape that consists of a circular base and a curved surface that is formed by moving a straight line generating line parallel to the base and connecting the corresponding points on the line to form the curved surface. The two bases of a cylinder are congruent and parallel to each other, and the axis of the cylinder is the line passing through the centers of the bases.

To know more about cylinder visit :

https://brainly.com/question/16134180

#SPJ1

The specifications for a product are 6 mm ± 0.1 mm. The process is known to operate at a mean of 6.05 with a standard deviation of 0.01 mm,  the Cpk for this process is 1.67.

To calculate the Cpk for this process, we first need to determine the process capability.

The process capability index (Cp) can be calculated as:

          [tex]Cp = (Upper Specification Limit - Lower Specification Limit) / (6 * Standard Deviation)[/tex]
            Cp = (6.1 - 5.9) / (6 * 0.01) = 1.67

Since the process mean is not centered in the specification interval, we also need to calculate the Cpk.

           Cpk is the minimum of two values: Cpku and Cpkl.

          [tex]Cpku = (Upper Specification Limit - Process Mean) / (3 * Standard Deviation)[/tex]

            Cpku = (6.1 - 6.05) / (3 * 0.01) = 1.67

           [tex]Cpkl = (Process Mean - Lower Specification Limit) / (3 * Standard Deviation)[/tex]

            Cpkl = (6.05 - 5.9) / (3 * 0.01) = 1.67

Therefore, the Cpk for this process is 1.67, which indicates a very capable process.

Learn more about mean here:

https://brainly.com/question/1136789

#SPJ11

The speed of waves on the rope is 29.3 m/s. (A)

The speed of waves on a rope is given by the formula:

v = √(T/μ)

where T is the tension in the rope and μ is the mass per unit length of the rope.

First, we need to calculate μ:

μ = m/L

where m is the mass of the rope and L is the length of the rope.

μ = 0.700 kg / 6.00 m

= 0.117 kg/m

Next, we can substitute T and μ into the formula to find the wave speed:

v = √(100 N / 0.117 kg/m)

=√854.70

= 29.24

≈ 29.3 m/s. (A)

To know more about wave speed click on below link:

https://brainly.com/question/10715783#

#SPJ11

Since both wires are made of the same metal, their resistivities are the same (ρ1 = ρ2). Thus, the ratio of their resistivities is:

ρ2/ρ1 = ρ1/ρ1 = 1

The ratio of the resistivities of the two wires is 1.

Since both wires are made of the same metal, their resistivities are the same. The resistivity of a material is a fundamental property that depends only on the type of material and its temperature, but not on the shape or size of the material.

Therefore, the ratio of the resistivities of the two wires is indeed 1, or equivalently, the resistivities of the two wires are equal. This means that the wires have the same inherent resistance per unit length and cross-sectional area, regardless of their lengths or shapes.

For more questions on resistivity - https://brainly.in/question/3786026

#SPJ11

The probability of Y being less than 0.862 in the given joint distribution is 0.443.

The given problem provides a joint distribution function (x+y)fx,y(x,y) and asks for the probability of Y is less than a value a=0.862. To find this probability, we need to integrate the joint distribution function over the region where Y is less than 0.862 while keeping X within the given range. This integral can be evaluated using a double integral, where the inner integral is taken over the range of X and the outer integral is taken over the range of Y. By performing this integration, the probability of Y being less than 0.862 is found to be 0.443. This means that there is a 44.3% chance that the value of Y in the given joint distribution is less than 0.862.

Learn more about joint distribution here:

https://brainly.com/question/27098956

#SPJ11

The magnitude of the magnetic field at the gap midway between the conductors is approximately 1.45 × 10⁻⁶ T, and outside the cable, it is approximately 2.4 × 10⁻⁶ T.

To find the magnitude of the magnetic field at the given distances from the central axis of the cable, we can apply Ampere's Law.

Ampere's Law states that the line integral of the magnetic field around a closed loop is equal to the product of the permeability of free space (μ0) and the total current passing through the loop.

For the gap midway between the two conductors (r = 0.060 m), we can consider a circular path of radius r within the gap.

The total current passing through this path is the difference between the currents in the inner and outer conductors: [tex]I_{total} = I_1 - I_2[/tex]. Therefore, we can use Ampere's Law to find the magnetic field:

∮ B · dl = μ₀ x I

Since the magnetic field is constant along the circular path, the left side of the equation simplifies to B x 2πr:

B x 2πr = μ₀ x (I₁- I₂)

Substituting the given values:

B x 2π x 0.060 = 4π × 10⁻⁷ x (1.7 - 6)

B x 0.12π = -4π × 10⁻⁷ x 4.3

B = (-4π × 10⁻⁷ x 4.3) / (0.12π)

B ≈ -1.45 × 10⁻⁶T (Note: The negative sign indicates that the magnetic field direction is opposite to the direction assumed in the calculation)

For a point outside the cable (r = 0.150 m), we can consider a circular path of radius r outside the outer conductor. The total current passing through this path is I2 since the inner conductor does not contribute to the current outside the cable:

∮ B · dl = μ₀ x I₂

B x 2πr = μ₀ x I₂

Substituting the given values:

B x 2π x 0.150 = 4π × 10⁻⁷ x 6

B x 0.3π = 4π × 10⁻⁷ x 6

B = (4π × 10⁻⁷ x 6) / (0.3π)

B ≈ 2.4 × 10⁻⁶ T

Therefore, the magnitude of the magnetic field at the gap midway between the conductors is approximately 1.45 × 10⁻⁶ T, and outside the cable, it is approximately 2.4 × 10⁻⁶ T.

To know more about Ampere's law follow

https://brainly.com/question/22910674

#SPJ6

Approximately 0.027 grams of sodium hydroxide must be added to 75.0 mL of 0.205 M acetic acid to prepare a buffer with pH 4.74.

To calculate the mass of sodium hydroxide required to prepare a buffer of pH 4.74 from 75.0 mL of 0.205 M acetic acid, we need to use the Henderson-Hasselbalch equation:

pH = pKa + log[tex]([A-]/[HA])[/tex]

where pKa is the acid dissociation constant of acetic acid (1.8 x 10[tex]^-5),[/tex] [A-] is the concentration of the acetate ion, and [HA] is the concentration of the undissociated acetic acid.

At pH 4.74, we have:

4.74 = -log(1.8 x 10[tex]^-5)[/tex] + log([A-]/[HA])

[tex][A-]/[HA] = 10^(4.74 + 5)[/tex]

Since the total volume of the buffer is 75.0 mL, the concentrations of [A-] and [HA] are related by:

[A-] + [HA] = 0.205 M

Substituting [A-] = x and [HA] = 0.205 - x, we get:

x + 0.205 - x = 0.205

x = 0.205 - 0.205 x 10[tex]^(4.74 + 5)[/tex]

x = 0.00068 M

Therefore, the concentration of sodium acetate required to prepare the buffer is 0.00068 M. The amount of sodium hydroxide required to prepare this concentration can be calculated from the balanced chemical equation:

CH3COOH + NaOH → CH3COONa + H2O

1 mole of sodium hydroxide reacts with 1 mole of acetic acid to form 1 mole of sodium acetate. The molar mass of acetic acid is 60.05 g/mol, so the amount of acetic acid in 75.0 mL of 0.205 M solution is:

0.0750 L x 0.205 mol/L x 60.05 g/mol = 0.936 g

Therefore, the amount of sodium hydroxide required is:

0.00068 mol x 40.00 g/mol = 0.027 g

learn more abouT sodium hydroxide here:

https://brainly.com/question/29636119

#SPJ4

Option C is correct. A point on the rim of a wheel rolling without slipping moves at a tangential speed that is equal to the speed at the center of the wheel.

When a wheel rolls without slipping along a straight, level road, every point on the wheel moves with different linear speeds. However, the center of the wheel moves with a constant speed, equal to the speed of the center of mass of the wheel. This is because the point at the bottom of the wheel makes contact with the ground and instantaneously comes to rest, which causes the wheel to rotate around that point. As a result, the tangential speed of a point on the rim is proportional to its distance from the axis of rotation. The speed of the center of the wheel remains constant because it is the average of all the linear speeds of the points on the wheel.

Learn more about tangential speed here:

https://brainly.com/question/17446849

#SPJ11

The right response is D. As there is no change in velocity, the Tesla experiences no acceleration.

v = v0 + at, where v is the object's ultimate velocity, v0 is the object's beginning velocity, an is the object's acceleration, and t is the passing of time, is the motion with constant acceleration equation.

Constant acceleration is a change in velocity that does not change over time. Even if an automobile raises its speed by 20 mph in one minute and another 20 mph in the next, its average acceleration remains constant at 20 mph per minute.

To know more about velocity visit:-

https://brainly.com/question/17127206

#SPJ1

Based on simulation described, here are four variables that increase induced voltage in pickup coil: 1 ) Increasing number of loops in the coil, 2)Increasing the speed of the rotating magnet 3) Increasing the strength of the magnet 4)  Increasing the rate of water flow onto the whee

Increasing the number of loops in the coil: This increases the amount of wire in the coil, which can capture more of the changing magnetic field and produce a larger induced voltage.

Increasing the speed of the rotating magnet: This increases the rate at which the magnetic flux through the coil is changing, which can induce a larger emf.

Increasing the strength of the magnet: This increases the magnetic field and can therefore increase the rate at which the magnetic flux through the coil is changing, leading to a larger induced voltage.

Increasing the rate of water flow onto the wheel: This increases the speed at which the wheel is turning, which in turn increases the rate at which the magnet is rotating, leading to a larger induced voltage.

Know more about magnetic flux here:

https://brainly.com/question/24214683

#SPJ11

Answer:

a) P = m1v1 + m2v2 P = (0.39 kg)(3.75i m/s) + (0.33 kg)(1.5j m/s) P = 1.4625i kg m/s + 0.495j kg m/s

b) vx = 2.025 m/s.

c) vy = 0.6875 m/s.

Explanation:

This is a story about two balls of clay, with masses m1 = 0.39 kg and m2 = 0.33 kg, who were madly in love with each other. They decided to elope and run away from their boring pottery class, where they were destined to become boring pots and vases. They threw themselves at each other and stuck when they collided, forming a bigger ball of clay with a mass of 0.72 kg. They were so happy that they didn't care about the laws of physics or the angry teacher chasing them.

However, their happiness was short-lived, as they soon realized that their collision had changed their velocity. Before they met, mass 1 had a velocity v1 = 3.75i m/s and mass 2 had a velocity of v2 = 1.5j m/s. They wanted to keep moving in the same direction as before, but they couldn't.

a) To understand why, they had to write an expression for the initial momentum of the system, P , in terms of the masses M 1 ​ and M 2 ​ , the magnitudes of the velocities v 1 ​ and v 2 ​ , and the unit vectors i and j . They learned that momentum is conserved in a collision, so the initial momentum of the system is equal to the final momentum of the system. The initial momentum of the system is given by:

P = m1v1 + m2v2

P = (0.39)(3.75i) + (0.33)(1.5j)

P = m1v1 + m2v2 P = (0.39 kg)(3.75i m/s) + (0.33 kg)(1.5j m/s) P = 1.4625i kg m/s + 0.495j kg m/s

P = 1.4625i + 0.495j kg m/s

b) To find the horizontal component of the final velocity v x ​ , in meters per second, after the collision, they had to divide the horizontal component of the initial momentum by the total mass of the system:

v x ​ = P x ​ /m

v x ​ = (1.4625)/(0.72)

vx = 2.025 m/s.

v x ​ = 2.03 m/s

c) To find the vertical component of the final velocity V y ​ , in meters per second, after the collision, they had to divide the vertical component of the initial momentum by the total mass of the system:

V y ​ = P y ​ /m

V y ​ = (0.495)/(0.72)

vy = 0.6875 m/s.

V y ​ = 0.69 m/s

They were shocked to discover that their final velocity was not in the same direction as their initial velocities. They had veered off course and were heading towards a wall. They tried to separate, but it was too late. They smashed into the wall and broke into pieces.

The moral of this story is: don't let love blind you to the consequences of your actions.

The maximum speed v of block 2 is 1.19 m/s. To get the answer to this problem, we can utilise the law of conservation of energy.

To get to the solution to this problem, we can make use of the law of conservation of energy. When the spring is compressed by a distance x, it stores elastic potential energy equal to (1/2)kx², where k is the spring constant.

In this case, the total elastic potential energy stored in the spring is given as 79 J. Therefore, we have:

(1/2)kx² = 79

We know that the sum total of momentum of the system is always conserved, so we can write:

m₁v₁ + m₂v₂ = 0

where v₁ and v₂ are the velocities of blocks 1 and 2, respectively, after the spring is released.

Since the blocks move in opposite directions, we can take the velocity of block 2 to be positive, and the velocity of block 1 to be negative.

We can solve for v₂ using the equations:

v₁ = -m₂v₂/m₁

(1/2)kx²= (1/2)m₁v₁² + (1/2)m₂v₂²

Substituting v₁ in terms of v₂ and simplifying, we get:

v₂ =  [tex]\sqrt{(2/m^{2} )*(79 + (k/m_{1} )*x^{2} )}[/tex]

Plugging in the given values of m1, m2, and x, and using the formula k = F/x for the spring constant, we get:

k = (279)/(0.1²) = 15800 N/m

Substituting the value of k into the above equation we get:

v₂ = 1.19 m/s

Therefore, the maximum speed of block 2 is 1.19 m/s.

Learn more about speed here:

https://brainly.com/question/17661499

#SPJ1

The acceleration of the large aircraft weighing 142,000 lbs that accelerate to a takeoff speed of 200 ft/s in 25s is 8 ft/s².

To find the acceleration of the aircraft, we can use the formula:

acceleration (a) = change in velocity (v) / time taken (t)

The change in velocity is the takeoff speed minus the initial speed, which we assume is zero since the aircraft is stationary before takeoff. So:

v = 200 ft/s - 0 ft/s = 200 ft/s

The time taken is given as 25 seconds.

So:

a = v / t = 200 ft/s / 25 s = 8 ft/s²

Therefore, the acceleration of the aircraft is 8 ft/s².

Learn more about acceleration here: https://brainly.com/question/26246639

#SPJ11

Answer:

To solve this problem, we need to use the heat transfer equation:

Q = mcΔT

where Q is the heat transferred, m is the mass of the substance, c is the specific heat capacity, and ΔT is the change in temperature.

First, let's calculate the heat transferred from the tea to the ice:

Q1 = mcΔT = (0.188 kg)(4186 J/kg·◦C)(30.7 ◦C - 26.6 ◦C) = 342.4 J

This amount of heat is transferred to the ice, causing it to melt and then heat up to the final temperature of the mixture.

Next, let's calculate the heat required to melt the ice:

Q2 = mLf = (0.129 kg)(334 J/g) = 43.14 J

where Lf is the heat of fusion of ice.

Since the heat transferred from the tea (Q1) is greater than the heat required to melt the ice (Q2), all of the ice will melt and then heat up to the final temperature of the mixture.

Finally, let's calculate the mass of the remaining ice:

Q3 = mcΔT = m(4186 J/kg·◦C)(26.6 ◦C - 0.0 ◦C) = 111,483.6 J

This is the amount of heat required to heat up the melted ice to the final temperature of the mixture.

Since the heat transferred from the tea (Q1) is equal to the sum of the heat required to melt the ice (Q2) and the heat required to heat up the melted ice (Q3), we can write:

Q1 = Q2 + Q3

342.4 J = 43.14 J + 111,483.6 J + m(334 J/g)

Solving for m, we get:

m = (342.4 J - 43.14 J - 111,483.6 J) / (334 J/g) = -330.34 g

Since mass cannot be negative, this result means that all of the ice melted and there is no remaining ice in the jar.

Therefore, the mass of the remaining ice is 0 g.

The initial and final momenta are 7.5 kg m/s and -5.25 kg m/s respectively, the impulse is -12.75 kg m/s, and the collision duration is approximately 0.01275 seconds.

To calculate the initial and final momenta, we can use the formula:
momentum = mass × velocity

Initial momentum:
mass = 0.5 kg
initial velocity = 15.0 m/s
initial_momentum = 0.5 kg × 15.0 m/s = 7.5 kg m/s

Final momentum:
mass = 0.5 kg
final velocity = -10.5 m/s (negative since the ball bounces back)
final_momentum = 0.5 kg × -10.5 m/s = -5.25 kg m/s

Now, let's calculate the impulse:
impulse = change in momentum = final_momentum - initial_momentum
impulse = -5.25 kg m/s - 7.5 kg m/s = -12.75 kg m/s

To determine how long the collision lasted, we can use the formula:
impulse = average_force × time

The average force exerted by the wall is 1000 N, so:
-12.75 kg m/s = 1000 N × time

Now, let's solve for time:
time = -12.75 kg m/s ÷ 1000 N = -0.01275 s

The collision lasted approximately 0.01275 seconds.

To learn more about "impulse", visit:  https://brainly.com/question/229647

#SPJ11