Answer:
nope, it is phsically impossible for water to be on mars
Explanation:
If we have to become a pilot what class should we choose
.
Science,
economics,
or commerce
Answer:
Class Not Necessary For Army
Explanation:
Just a normal degree is enough
Answer:
Degree Is Enough
Explanation:
Bcz of There is Class
Plzz help me plzzzz plzz
Answer:
A. Air powered
Explanation:
Pneumatic tools are compressed air driven power tools powered by an air compressor.
an automobile radiator is filled to the brim with water when the engine is cool. what happens to the water when the engine is running and the water has been raised to a high temperature?
Answer:
(a) As the water rises in temperature, it expands or rises in pressure or both. The excess volume would spill out of the cooling system, or else the pressure would rise very high indeed.
(b) Modern cooling systems have an overflow reservoir to accept the excess volume when the coolant heats up and expands.
Explanation:
hope it helps!
Water expands more when the temperature is elevated, increasing its volume. Consequently, the steel radiator will leak water. When the engine is running, the water is heated to higher temperatures, which causes it to expand and spill out.
What engine is running, the water raised to a temperature?Your engine should operate between 195 and 220 degrees, according to the majority of experts. Your needle should always remain centered in your gauge in ideal circumstances.
A thermostat, cylinder sleeve, cooling water pump, and heat exchanger are all components of an engine cooling water system. Water System for Engine Cooling. The cooling water must be circulated throughout the engine by a cooling water pump.
Therefore, This is due to the fact that radiator water will freeze when temperatures in colder countries fall below zero degrees, which is the freezing point of water.
Learn more about engine here:
https://brainly.com/question/2973143
#SPJ2
Please help meeeplzzzzzz
Answer:
labelled diagram for combination wrench
State three means of operating a power tool
How do people put virus
Answer:
Explanation:
Don’t know
On diesel engines, data from ________ sensors are commonly used to adjust exhaust gas recirculation (EGR) rates.
Answer:
Air mass sensors is the right answer i think
Explanation:
Some benefits of science
Answer:
Scientific knowledge allows us to develop new technologies, solve practical problems, and make informed decisions — both individually and collectively. Because its products are so useful, the process of science is intertwined with those applications: New scientific knowledge may lead to new applications.
Explanation:
Which of the following is a type of Interior door?
Answer:
There is no answers given
Explanation:
Multiple Choice
1.
is light-gauge metallic tube used to route wires.
A. Electrical metallic tubing (EMT)
B. Flexible metal conduit (FMC)
C. Rigid metal conduit (RMC)
D. Polyvinyl chloride (PVC) conduit
Answer:
I guess A number is right
State three means of operating a power tool
Another way to consider power tools is by the energy they use to function. Power tools usually run on one of three types of power: compressed air, electricity, or combustion.
Answer:
answer is given below
Explanation:
Power tools usually run on one of three types of power: compressed air, electricity, or combustion.
soy nueva en esto me pudieran ayudar nadie me ayuda soy de peru y no endiendo nada de lo que me dicen alguie me puediera explicar como se utiliza esta fuente y si me pudiera guir y ser mi amigos o amiga para que me ayude , le agradecira un monton
Answer:
Explanation:
Tu pon lo que ocupes y espera
How to handle or hold sharp edged tools in welding
Answer: I got you bestie :)
When walking with a sharp tool, the tool should be carried with the blade down and away from the body. When climbing with a sharp tool, tool belts, or buckets with hand lines should be used so workers can have both hands to grip the ladder.
Answer:
sharp egdes should be held far from the body just in case you fall you won't really get cut by it
Explanation:
thanks for the points
What is the difference between bare and
shielded electrodes
Answer:
shielded electrodes give metal smotth and clean welds and bare electrodes reduces spattering.
Explanation:
Shielded electrodes minimize sulfur, oxides, and other types of impurities within the base metal to give regular, smooth, and clean welds while bare electrodes, makes welding more manageable and reduces spattering
Fill in the blank with the correct response.
__________involves gathering and analyzing information related to the terrain and environment of enemy forces.
Answer:
Intelligence
Explanation:
What was jimmy neutron's first invention?
Answer:
oh i like this film
Explanation:
ye ye
what is the first step of the engineering design process?
Answer:
The first step is to identify the need and constraints
Explanation:
What is true about a point and shoot camera?
They always have lenses u can take on and off
They are often smaller than SLR cameras
They are used by professionals more often that SLR cameras
All of the above
Answer:
What is true about a point and shoot camera?
They are often smaller than SLR camerasAnswer:
They are often smaller than SLR cameras
Explanation:
What is energy security, and why is it an important issue for many countries?
Answer:
What is energy security? Energy security is the association between national security and the availability or natural resources for energy consumption.
why is it an important issue for many countries? To ensure that their economics function without interruption and that their people have access to adequate, reliable and affordable supplies of modern and clean energy
Cooling water available at 10°C is used to condense steam at 30°C in the condenser of a power plant at a rate of 0.60 kg/s by circulating the cooling water through a bank of 7-m-long 1.2-cm-internal-diameter thin copper tubes. Water enters the tubes at a mean velocity of 4 m/s and leaves at a temperature of 24°C. The tubes are nearly isothermal at 30°C. Determine the average heat transfer coefficient between the water, the tubes, and the number of tubes needed to achieve the indicated heat transfer rate in the condenser.
Answer:
Dang this looks hard
Explanation:
how to clean corroded battery terminals in electronics
State three means of operating a power tool
State three means of operating a power tool
Answer:
A power tool is a tool that is actuated by an additional power source and mechanism other than the solely manual labor used with hand tools. The most common types of power tools use electric motors. Internal combustion engines and compressed air are also commonly used. Other power sources include steam engines, direct burning of fuels and propellants, such as in powder-actuated tools, or even natural power sources such as wind or moving water. Tools directly driven by animal power are not generally considered power tools.
Power tools are used in industry, in construction, in the garden, for housework tasks such as cooking, cleaning, and around the house for purposes of driving (fasteners), drilling, cutting, shaping, sanding, grinding, routing, polishing, painting, heating and more.
Power tools are classified as either stationary or portable, where portable means hand-held. Portable power tools have obvious advantages in mobility. Stationary power tools, however, often have advantages in speed and precision. A typical table saw, for instance, not only cuts faster than a regular hand saw, but the cuts are smoother, straighter, and more square than what is normally achievable with a hand-held power saw. Some stationary power tools can produce objects that cannot be made in any other way. Lathes, for example, produce truly round objects.
Stationary power tools for metalworking are usually called machine tools. The term machine tool is not usually applied to stationary power tools for woodworking, although such usage is occasionally heard, and in some cases, such as drill presses and bench grinders, exactly the same tool is used for both woodworking and metalworking.
Explanation:
Explain the purpose of wrench plzzz
Answer:
Wrenches are made in various shapes and sizes and are used for gripping, fastening, turning, tightening and loosening things like pipes, pipe fittings, nuts and bolts. There are basically two major kinds of wrenches: Pipe wrenches used in plumbing for gripping round (cylindrical) things.
if we model the vibrating system as a mass on a spring, what is the mass necessary to achieve the desired resonant frequency when the tip is not interacting with the surface?
Answer:
2.5 micrograms
Explanation:
The frequency of a vibrating body reduces with increasing mass, but increases with increasing tension.
What is the relation of resonant frequency with mass?For a spring-mass system, the relationship between frequency and mass can be expressed as follows: as mass increases, frequency decreases; as mass decreases, frequency increases.
The frequency in this case is f, and the mass is m. The relationship between mass and frequency is therefore inverse.
Precession frequency drops when mass is doubled, since angular momentum also doubles at this point. As the radius grows, the angular momentum increases and the precession frequency decreases.
Mass and stiffness are two well-known factors that affect an object's resonance frequency.
While stiffness limits low-frequency transmission because less elastic, or stiff, materials vibrate at higher frequencies, mass limits high-frequency transmission because larger objects vibrate at lower frequencies.
Therefore, The resonant frequency should rise as mass decreases.
Learn more about frequency here:
https://brainly.com/question/13191113
#SPJ5
A resistance of 30Ω is placed in a circuit with a 90 volt battery. What current flows in the circuit?
Answer:
30 Amperes
Explanation:
if V ⇒ voltage
I ⇒ current
R ⇒ resistance
V = IR
90 = I x 30
90/30 = I
3 = I
Technician A says that comparing the front vehicle height sensors to the rear sensors allows the ECM to determine body roll created by cornering force. Technician B says that vehicle height sensors are only located on the rear. Which technician is correct
Answer:
its b
Explanation:
when the filament breaks in one lamp in a series circuit, other lamps in the circuit normally _________.
Answer:
when the filament breaks in one lamp in a series circuit, other lamps in the circuit normally stop working.
Explanation:
Concrete has a higher specific heat than does soil. Use this fact to explain (partially) why a city has a higher average temperature than the surrounding countryside.
Answer:
Since concrete has higher specific heat, it will absorb more heat and the temperatures will rise in proportion. The large amount of energy stored in concrete during the day as the sun falls on it is released at night, resulting in an higher average evening temperature than the countryside. The cool air in the surrounding countryside exerts a buoyant force on the warmer air in the city, pushing it upward and moving into the city in the process. Thus, evening breezes tend to blow from country to city.
Explanation:
The city has a higher average temperature than the surrounding countryside as most of the cities are made up of concrete designs one of the things which absorb a lot of heat.
What is soil?Soil contains lots of minerals as well as microorganisms. One can grow crops or vegetation on the soil. This is made up of various types of sand and granules that can be present.
Concrete absorbs more heat because of its high surface heat, which causes temperatures to rise proportionately. Asphalt absorbs a lot of energy generated by the sun each day and releases it at night, giving cities a warmer average nighttime weather than rural.
The heated air in the city is propelled higher and toward the city by the density of water of the cooler in the nearby countryside. As a result, evening gusts frequently travel between rural to city.
Learn more about Soil, here:
https://brainly.com/question/224605
#SPJ5
My cramps hurt sm and I’m so emotional
Answer:
Okay? I can try to help you.
Go to sleep.Cry in pain.I hope this helped at all.
Answer:
Man up you women. Eat some travis scuout burjer