Raw sugar cane is taken into a process to create sugar, which is essentially sucrose. the raw cane is approximately 16% sucrose, 63% water, and the rest fiber by mass. juice from the cane is extracted by passing the cane through a series of crushers. about 5% extra mass of water is added to the sugar cane prior to this step to help in the extraction process. the crushed cane and liquid juice is sent to a filter press that creates a cake that contains 4% of the weight of the cane juice, which has a composition similar to the overall non-fiber content of the raw cane. the filtrate is sent to an evaporator where enough water is evaporated to obtain a pale yellow juice that is 41% water. A series of vacuum processes removes enough water without damaging the sugars until you obtain a solution that is 91% sucrose. At this point, the mixture is fed to a crystallizer to produce a final product of sucrose that is 97.8% crystal. You control the process by measuring the flowrate of the solution into the crystallizer using a manometer that has mercury as the working fluid. The open-ended manometer shows a mercury height difference of 6.3 inches, , while the height of the sucrose solution in the manometer between the mercury and the pipe is 15.3 in.
The flowrate of the mixture into the crystallizer is related to the pressure with the following equation:
q(m^3/s) = 0.0307 m^3/hr atm^1/2 √ Pmanometer
What is the mass of sugar cane being fed to the process with this flowrate, in kg/s?

Answer:

i like icecream

Explanation:

__________________________________________________________

Hello! In this question, I will answer the first part of the question, in which we will determine the x, y, and z components for the reaction at joint A in the ball-and-socket.
__________________________________________________________

Explanation:

To better understand what the question entails, we will start off by drawing the free-body diagram to understand the direction of our components. The image is attached below. This will help us solve for our components.

__________________________________________________________

Solve:

To start, we will first solve for the weight of the sign, we will use the formula:

[tex]W=mg[/tex]

Whereas:

Plug in our values into the formula and solve:

[tex]W = 90\cdot9.81=882.9 N[/tex]

Since we now know our weight value, we can solve for our force in the cable BC, expressed as a vector. We will use the formula:

[tex]\bold{T}_{BC}=T_{BC}(\frac{\bold{r}_{BC}}{r_{BC}})[/tex]

Where:

Plug in our values into the formula and solve:

[tex]\bold{T}_{BC}=T_{BC}\bigg(\cfrac{\text{[i - 2j+ 2k] ft}}{\sqrt{(1)^2+(-2)^2+(2)^2}}}\bigg)\\\\\bold{T}_{BC}=T_{BC}\bigg(\cfrac{\text{[i - 2j+ 2k] ft}}{3}}}\bigg)\\\\\text{Simplify}\\\\\bold{T}_{BC}=\frac{1}{3}T_{BC}{\text{i}}-\frac{2}{3}T_{BC}j+\frac{2}{3} T_{BC}k[/tex]

Now, let us solve for our force in the cable BD, also expressed as a vector. Use the formula:

[tex]\bold{T}_{BD}=T_{BD}(\frac{\bold{r}_{BD}}{r_{BD}})[/tex]

Use the same steps from solving for our vector force of cable BC. Plug in the values and solve:

[tex]\bold{T}_{BD}=T_{BD}\bigg(\cfrac{\text{[-2i - 2j+ k] ft}}{\sqrt{(-2)^2+(-2)^2+(1)^2}}}\bigg)\\\\\bold{T}_{BD}=T_{BD}\bigg(\cfrac{\text{[-2i - 2j+ k] ft}}{3}}}\bigg)\\\\\text{Simplify}\\\\\bold{T}_{BD}=-\frac{2}{3}T_{BD}{\text{i}}-\frac{2}{3}T_{BD}j+\frac{1}{3} T_{BD}k[/tex]

We now need to find the moment at A at equilibrium (0). This is known as:

[tex]\sum M_{a}=0 \Rightarrow\bold{r}_{B}\times(\bold{T}_{BC}+\bold{T}_{BD}+\bold{W})=0[/tex]

Whereas:

Plug in values into the equation:

[tex]2\text{j}\times\big[\big(\frac{1}{3}T_{BC}{\text{i}}-\frac{2}{3}T_{BC}j+\frac{2}{3} T_{BC}k\big)+\big(-\frac{2}{3}T_{BD}{\text{i}}-\frac{2}{3}T_{BD}j+\frac{1}{3} T_{BD}k\big)\big]\\+\text{j}\times-882.9\text{k}=0[/tex]

Find the moment about the z-axis to zero. This is known as:

[tex]\sum M_{z}=0\\\\-\frac{2}{3}T_{BC}+\frac{4}{3}T_{BD}=0\\\\\text{Simplify}\\\\T_{BC}=2T_{BD}[/tex]

Now, find the moment about the x-axis to zero. This is known as:

[tex]\sum M_{x}=0\\\\\frac{4}{3}T_{BC}+\frac{2}{3}T_{BD}-882.9=0\\\\\text{We know }T_{BC}=2T_{BD}\text{, plug in }2T_{BD}\text{ in }T_{BC}\\\\\frac{4}{3}\times2T_{BD}+\frac{2}{3}T_{BD}-882.9=0\text{ Solve for }T_{BD}\\\\\frac{10}{3}T_{BD}=882.9\\\\T_{BD}=264.87\text{ N}[/tex]

Now, let us calculate the tension in wire BC.

[tex]T_{BC}=2T_{BD} = 2(264.87) = 529.74\text{ N}[/tex]

Let us calculate the reaction at A by solving for the equilibrium force equation. The formula is:

[tex]\sum F=0\\\\\bold{F}_A+\bold{T}_{BC}+\bold{T}_{BD}+\bold{W}=0[/tex]

Plug in our known information into the equation and simplify.

[tex]\big[(A_xi+A_yj+A_zk)+(\frac{1}{3}T_{BC}{\text{i}}-\frac{2}{3}T_{BC}j+\frac{2}{3} T_{BC}k)+(-\frac{2}{3}T_{BD}{\text{i}}-\frac{2}{3}T_{BD}j\\+\frac{1}{3} T_{BD}k)-981\text{k}\big]=0\\\\\text{Separate by component}\\\\\big[(A_x+\frac{1}{3}T_{BC}-\frac{2}{3}T_{BD})\text{\bold{i}}+(A_y-\frac{2}{3}T_{BC}-\frac{2}{3}T_{BD})\text{\bold{j}}+(A_z+\frac{2}{3}T_{BC}+\frac{1}{3}T_{BD}\\-981)\text{\bold{k}}\big]=0\\\\\text{Plug in known values}\\[/tex]

[tex]\big[(A_x+\frac{1}{3}\times529.74-\frac{2}{3}\times264.87)\text{\bold{i}}+(A_y-\frac{2}{3}\times529.74-\frac{2}{3}\times264.87)\text{\bold{j}}+(A_z+\frac{2}{3}\times529.74+\frac{1}{3}\times264.87-882.9)\text{\bold{k}}\big]=0[/tex]

Now, we can calculate our reactions.

Calculate the reaction at A in the x-direction.

[tex]\sum F_x=0\\\\A_x+\frac{1}{3}\times529.74-\frac{2}{3}\times264.87=0\\\\\boxed{A_x=0\text{ N}}[/tex]

Calculate the reaction at A in the y-direction.

[tex]\sum F_y=0\\\\A_y-\frac{2}{3}\times529.74-\frac{2}{3}\times264.87=0\\\\A_y-529.74=0\\\\\boxed{A_y=529.74\text{ N}}[/tex]

Calculate the reaction at A in the z-direction.

[tex]\sum F_z=0\\\\A_z+\frac{2}{3}\times529.74+\frac{1}{3}\times264.87-981=0\\\\A_z-441.45=0\\\\\boxed{A_z=441.45\text{ N}}[/tex]

__________________________________________________________

Answer:

[tex]\boxed{\text{A=} < \text{0, 529.74, 441.45} > }[/tex]

__________________________________________________________

Regardless of whether a default static route is set up, the "default-information originate" command is used to advertise a default route into OSPF.

Static routing is the practice of using a manually specified routing entry rather than information from traffic generated by dynamic routing. Although it isn't always the case, network administrators frequently manually configure static routes in addition to adding entries to a routing table. In contrast to dynamic routing, static routes have been fixed and remain the same despite network configuration changes. Static and dynamic routing are not mutually exclusive. A router often combines both dynamic routing and static routing to maximize routing efficiency and provide fall backs in the case that dynamic routing information cannot be transmitted. As a last-resort gateway or in stub networks, static routing may also be used.

Learn more about Static routing here:

https://brainly.com/question/29359545

#SPJ4

Yes, that's correct. THD is typically expressed as a percentage, with lower values indicating a cleaner signal with less distortion.

Total harmonic distortion (THD) is a measure of the harmonic distortion present in a signal and is defined as the ratio of the sum of the powers of all harmonic components to the power of the fundamental frequency.

Total harmonic distortion (THD) is a measure of the harmonic distortion present in a signal and is defined as the ratio of the sum of the powers of all harmonic components to the power of the fundamental frequency. THD is typically expressed as a percentage, with lower values indicating a cleaner signal with less distortion.

Complete question:

When harmonic distortion is specified as a composite value representing all the harmonics, it is called total harmonic distortion. ¿True or false?

Learn more about THD:

https://brainly.com/question/16045097

#SPJ4

After considering ϕϕ simply as a function, its domain is ⇒  [-4 , ∞).

When one or more functions and their derivatives are included in a mathematical equation, it is referred to as a differential equation. A function's derivatives at a given point determine how quickly the function will change.

Physicists, engineers, and biologists use it most frequently. Differential equations are primarily used to analyse solutions that satisfy the equations as well as the characteristics of the solutions. The differential equation can be solved in a variety of ways, but one of the simplest is by using explicit formulas.

y = x + 6√(x + 4)

⇒  y' = 1 + 6[ 1/(2√(x + 4))]      since d/dx xn = nxn-1 , d/dx √x = 1/(2√x)

⇒  y' = 1 + 3/√(x + 4)

(y -x)y' = (6√(x + 4))(1 + 3/√(x + 4)) = 6√(x + 4) + 18

y-x+18 = 6√(x + 4) + 18

ϕ(x) = x + 6√(x + 4)

Domain ⇒  x + 4 >= 0 ⇒  x >= -4

⇒ Domain ⇒  [-4 , ∞)

Learn more about Domain

https://brainly.com/question/28135761

#SPJ4

It is important to know the number of teeth on the two gears when calculating a bevel gear because the number of teeth determines the gear ratio, which in turn determines the torque and speed at which the gears will operate.

The gear ratio is calculated by dividing the number of teeth on the driving gear by the number of teeth on the driven gear.

If the number of teeth is not known, it would be impossible to accurately calculate the gear ratio and determine the performance of the gear set.

Additionally, the number of teeth also affects the meshing pattern and the contact ratio between gear teeth, which is also important to the gear's performance.

Read more about gear teeth here:

https://brainly.com/question/12761665

#SPJ1

The ionic radius of Ca²⁺ is 100 pm, K⁺ is 138 pm, Cl⁻ is 181 pm, and S²⁻ is 184 pm, therefore option d is the right choice.

The influence of an ion's nucleus on its electron cloud extends outward to a distance called the ionic radius.

When an atom loses or gains an electron, an ion is created. A cation is formed when an atom loses an electron, and an anion is formed when an atom gains an electron. The ionic radius is the furthest point away from the ion's nucleus that its outermost shell can extend.

A cation's atomic size will be lower than that of its parent atom. Compared to its parent atom, an anion is comparatively large. That's because the net effective nuclear charge gets drowned out by the repulsion between electrons caused by an atom gaining electrons.

Want to know more about ionic radius visit the link which is given below;

https://brainly.com/question/6637706

#SPJ4

The maximum load that a 0.50 inch diameter steel rod can support if the normal stress in the rod must not exceed 24,000 psi is 15,772 lb.

What is stress?
Stress in engineering is the amount of force that is applied to a material or structure. It is expressed in terms of pounds per square inch (psi) or megapascals (MPa). Stress can be caused by external forces such as gravity, wind, and temperature, as well as by internal forces such as tension, compression, and shear. When a material is stressed beyond its ability to contain the force, it will eventually fail. Engineers must consider a variety of factors when designing a structure or product to ensure that it can withstand the forces it will encounter in its intended environment. This includes understanding the properties of the materials being used, the effect of temperature and other environmental conditions, and the safety factors that must be applied to ensure the structure does not fail under extreme stress.

To learn more about stress
https://brainly.com/question/14288250

#SPJ4

Therefore, (-26.46i-52.92k) Nm is the answer to the presented problem of force.

The definition of force in physics is: The push or pull on a massed object changes its velocity. An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude.

Any of the four fundamental forces in physics—gravitational, electromagnetic, strong, and weak—that control how things or particles interact as well as how some particles decay—is referred to as a fundamental force, also known as a fundamental interaction. These fundamental forces are the source of all known natural forces.

to know more about force here:

brainly.com/question/13191643

#SPJ1

To determine whether the marketing campaign will add value to the business, the marketing agency should apply the Present Net Value formula.

A calculation known as the Present Net Value brings all of an investment's future cash flows to the present. The company must identify the revenue totally attributed to the marketing campaign in order to evaluate the campaign marketing strategy as a prospective investment. By doing this, the company will be able to determine the annual inflows (sales) that must be deducted from the outflows (marketing expenses). Every year's net value is discounted at a certain rate, and if the Present Net Value is more than 0, the marketing plan is anticipated to add value to the company. To determine whether the marketing campaign will add value to the business, the marketing agency should apply the Present Net Value formula.

Learn more about Present Net Value here:

https://brainly.com/question/14242912

#SPJ4

The energy of the magnetic and electric fields that have been stored can differ. A completely charged capacitor is linked in series with an inductor.

A passive-terminal electric device called an inductor, often referred to as a coil, choke, or reactor, stores electricity in a magnetic field when electric current passes through it. An insulated string twisted into a coil is typically included in an inductor. A passive digital component called an inductor can store electrical energy in the form of magnetic electricity. In essence, it uses a conductor that has been twisted into a coil; as electricity enters the coil from left to right, this will produce a magnetic field that rotates counter clockwise. The energy of the magnetic and electric fields that have been stored can differ.

Learn more about Inductor here:

https://brainly.com/question/29417056

#SPJ4

The data can be plotted as a standard curve. The concentration of Phenobarbital in the unknown can be determined by finding the point on the curve where the fluorescence of the solution intersects the x-axis.

a) The data is plotted in form of a standard curve, which is a graph of the fluorescence of the solutions versus the volume of the standard solution added.

b) By drawing a line of best fit through the data points, we can find the point where the line intersects the x-axis, the x-intercept, which will give us the concentration of phenobarbital in the unknown.

c) The least-squares equation is a mathematical representation of the line of best fit. It is used to find the relationship between two variables by minimizing the sum of the squared residuals between the data points and the line.

d) Using the equation obtained in c), we can calculate the concentration of phenobarbital in the unknown.

e) By using the residuals of the line of best fit, we can calculate the standard deviation of the concentration obtained in d). This will give us an idea of how much the concentration of phenobarbital in the unknown deviates from the actual value.

The least-squares equation can be found by fitting a line to the data points. The concentration of Phenobarbital can then be determined using this equation. The standard deviation for the concentration can be calculated using the residuals from the line of best fit.

Learn more about Phenobarbital here:

brainly.com/question/1939753

#SPJ4

A geotechnical investigation is primarily concerned with testing the physical properties of the soil, to provide recommendations for foundation requirements, excavation stability, drainage and buried concrete design.

Answer:

Geotechnical investigation is: A surface exploration and subsurface exploration of a site.

Explanation:

What does Geotechnical investigation mean?

It's a primarily concerned with testing the physical properties of the soil, to provide recommendations for foundation requirements, excavation stability, drainage and buried concrete design.

Why Geotechnical is important?

It allow's Engineers to evaluate the stability and strength of the ground, including slopes and soil deposits, assess risks such as soil aggressivity to buried concrete, and help to determine what type of foundations and earthworks would be required within a (project) for example.

Answer: The main difference between contact relays and communication relays is the type of signals that they are designed to handle, with contact relays being used to control the flow of electricity in a circuit and communication relays being used to transmit data or signals from one location to another.

Explanation: The main difference between contact relays and communication relays is the type of signals that they are designed to handle. Contact relays are used to control the flow of electricity in a circuit by opening and closing electrical contacts, while communication relays are used to transmit data or signals from one location to another.Contact relays are typically used in applications where it is necessary to switch electrical circuits on and off, such as in control panels and automated systems. They are usually designed to handle relatively low-frequency electrical signals and are typically not suitable for transmitting data or high-frequency signals.On the other hand, communication relays are used to transmit data or signals from one location to another, and are typically designed to handle a wide range of frequencies and data types. They can be used to transmit voice, data, and video signals over a variety of mediums, including wire, fiber optic cables, and wireless transmission.

Answer:

It is critical for the upper and lower end sections of an engine to work perfectly together because they are responsible for converting fuel into motion, which is necessary for the engine to operate effectively.

The upper end section of an engine includes the cylinder head and valves, which are responsible for controlling the flow of fuel and air into the engine. The lower end section of an engine includes the crankshaft, connecting rod, and pistons, which are responsible for converting the fuel's energy into rotational motion.

If the upper and lower end sections of an engine are not working perfectly together, it can lead to a variety of problems, including reduced engine performance, reduced fuel efficiency, and increased emissions. It is therefore critical for the upper and lower end sections to be carefully designed and calibrated to work together seamlessly in order to ensure the optimal performance of the engine.

Answer: B, plumb bob

Explanation:

A plumb bob's main job was to establish what is true (ie vertical and perpendicular to a surface,) as well as the secondary task of marking these points.

Compasses are mainly used to draw circles, protractors are used to measure angles, and rulers are used to measuring length.

Technician A is the correct answer. He is correct in saying that after an accident, you should take precautions to avoid it happening again in the future.

First, look for any injuries. If someone is in pain, take care of them.

After that, move your car to a safer location where you can exchange names, addresses, phone numbers, vehicle identification numbers, vehicle license plate numbers, insurance information, and driver's license information.

Finally, take note of the crash site and obtain the names, addresses, and phone numbers of any witnesses. If the vehicles cannot be moved, set up flares or raise your hood to protect the scene.

To know more about vehicle accidents, visit:

brainly.com/question/1235714

#SPJ4

gove it to me. I'll do my best

The statements below that refer to the design and operation of the power sub-system on a spacecraft is option

      7. For a spacecraft in planetary orbit, power for the eclipse period is commonly provided by a battery as a secondary power source, and an increased solar array area to give extra power to charge the batteries whilst not in eclipse.

Radioisotope Thermoelectric Generators (RTGS) are commonly applied to earth-orbiting spacecraft to provide power for the eclipse period when the solar panels are ineffective.

This is because RTGS use the heat generated by the decay of a radioactive material to generate electricity, which allows them to continue to produce power even when the solar panels are not receiving sunlight.

Therefore, Jupiter is considered the approximate limit for solar-powered orbital missions; missions to planets beyond this will require Radioisotope Thermoelectric Generators (RTGS). This is because as you move farther away from the sun, the amount of sunlight received by the solar panels decreases, making it difficult to generate enough power to operate the spacecraft. RTGS are a more reliable power source for missions to these outer planets because they do not rely on sunlight to generate power.

Learn more about spacecraft from

https://brainly.com/question/24571549

#SPJ1

The juice is then sent to a crystallizer where it is cooled and seeded with sugar crystals. The crystals grow in size and are separated from the liquid by centrifugation.

Crystallizer is a type of signal-processing technology most commonly used in audio production. It is designed to add clarity and definition to audio signals by emphasizing the frequencies which are most important to the signal. It works by amplifying the signal in the frequency domain and adding a process of resonance so that certain frequencies are emphasized, giving a more defined sound. Crystallizer is particularly useful in mastering, where it can bring out details and clarity that would otherwise be lost. It can also be used to enhance percussion instruments, making them more present in a mix.

The crystals are then dried and screened to obtain the desired size of sugar crystals. The remaining liquid is sent to a vacuum pan where it is boiled and evaporated until it reaches a concentration of 65% sucrose. The syrup is then cooled and crystallized to obtain the final product, which is refined sugar.

To learn more about crystallizers here:

brainly.com/question/13008800

#SPJ4

the battery and ODC input voltages, as well as the main parameters for the power source, fireworks, relays, anti-static resistances, etc. The statements below refer to the design and operation of the power sub-system on a spacecraft.

Solar panels on these spacecraft convert solar energy into the electricity they require for propulsion. The electricity generated by the solar panels is used to recharge a battery within the spacecraft. These batteries can power the spaceship even as it is traveling away from the sun.

The engine, temperature management, power and power distribution, attitude control, telemetry command and control, transmitters/antenna, computers/on-board processing/software, and structural components are only a few of the many subsystems that make up a spaceship bus.

To know more about spacecraft's subsystems visit:-

https://brainly.com/question/29610872

#SPJ1

Assuming the road is level, the driver must see the child at 300.3 ft to stop just in time. Hence, option C) is the correct answer.

The distance travelled between the moment the body decides to stop a moving vehicle and the moment the vehicle comes to a complete stop is known as the stopping distance. The stopping distance, indicated by the letter d, is dependent on a number of variables, including as the road's surface and the driver's reflexes.

The distance the car travels before coming to a halt is known as the stopping distance. It is depending on the vehicle's speed as well as the amount of road-to-wheel friction.

Deceleration rate is considered 11.2 ft/s²

a = 11.2 ft/s²

= 1^2/2 = (40 mi/h×5280 ft/1 mi×1 h/3600 s)²/22×11.2=240.07 ft

Stopping distance would be:

= 240.07+ 60.23 ft = 300.3 ft

To learn more about stopping distance visit:

brainly.com/question/24254597

#SPJ1

Answer: true

Explanation:

The energy stored in the two rubber bands of the catapult just before release can be calculated as follows: Area of Rubber Bands = (4 mm) x (300 mm) = 1200 mm2, Modulus of Rubber = 10-3 GPa = 10,000 N/mm2 Strain = (3 x Original Length) / (Original Length) =  Energy = (1200 mm2) x (10,000 N/mm2) x (3) = 36,000,000 Nmm or 36,000 J

Energy is the capacity of a physical system to do work or produce heat. It is the fundamental source of virtually all movement and change on Earth. In physics, energy is a property of objects which can be transferred to other objects or converted into different forms. Examples of energy include light, electricity, heat, sound, and kinetic energy. Energy can be generated from a variety of sources including fossil fuels, nuclear power, and renewable sources such as wind, solar, and hydropower. Energy plays a crucial role in the economic and social development of societies, enabling the production of goods and services and the delivery of basic services such as heating, cooling, and lighting. The efficient and responsible use of energy is essential to sustainable development.

To know more about energy here:

brainly.com/question/1932868

#SPJ4

Answer:

Programming paradigms are different approaches to programming. Each paradigm is concerned with the way code is written, structured, and organized. The main paradigms are procedural, object-oriented, functional, and logical. Each of these has its own set of rules and principles that guide how code is written and executed. Procedural programming focuses on implementing algorithms and breaking tasks down into smaller steps. Object-oriented programming focuses on breaking tasks down into objects and classes. Functional programming focuses on writing code that is easy to read and maintain. Logical programming focuses on using logic to solve problems.

Explanation:

Hope It Help You

Answer:

A programming paradigm is a style or approach to programming, characterized by the way in which the programmer writes the code. There are several different programming paradigms, including:

Explanation:

Imperative programming: This is the most traditional style of programming, in which the programmer writes code that specifies a series of steps to be carried out in order to solve a problem. Imperative programming languages include C, C++, and Java.

Object-oriented programming: In this style of programming, the programmer writes code in the form of objects, which are self-contained units that combine data and behavior. Object-oriented programming languages include Java, Python, and C#.

Functional programming: In functional programming, the programmer writes code in the form of functions, which are self-contained units that take input and produce output, without modifying any external state. Functional programming languages include Haskell, Lisp, and ML.

Logic programming: In this style of programming, the programmer writes code in the form of logical statements, and the language's runtime system is responsible for finding a solution that satisfies all of the statements. Logic programming languages include Prolog and Mercury.

Declarative programming: In declarative programming, the programmer specifies what the desired result should be, rather than how to achieve it. The language's runtime system is responsible for finding a way to produce the desired result. Declarative programming languages include SQL and regular expressions.

Answer:

it is okay depending on how u drive

Vector parts that are rectangular in shape are referred to as such if their axes are perpendicular to one another.

The rectangular components can be calculated algebraically or graphically, with the force represented as a vector. Knowing two of the six geometric characteristics of a triangle is necessary to resolve a vector into its components, Fx = F cos or Fy = F sin (the lengths of the sides and the three angles).

A vector's rectangular components are any two axes that are perpendicular to one another. An illustration of an example that demonstrates this is provided below. Additional Details: We have the magnitude of any two generic vectors' R's final formula is A2+B2+2ABcos.

To know more about  rectangular visit:-

https://brainly.com/question/11264478

#SPJ1

Two different kinds of losses can happen in a three-phase induction motor. These losses are variable losses that are constant or fixed losses. Fixed or Constant Losses Consta.

Stator losses, including as stator iron loss and stator copper loss, are financed in part by this power input. Rotor input is provided with the leftover power, or (input electrical power - stator losses). Thus, rotor input P2 equals Pin minus stator losses (stator copper loss and stator iron loss).

Fixed losses, Copper losses, and stray losses are a few types of losses that can occur in three-phase induction motors. Core losses, bearing friction losses, brush friction losses (in wound rotor motors), and windage losses make up the majority of these losses.

To know more about  induction motor visit:-

https://brainly.com/question/29664815

#SPJ1

Answer:

In a single-family residence, a line-voltage thermostat is primarily used to control heating and cooling systems.