Three point charges are arranged at the corners of a square of side L as shown in (Figure 1) What is the potential at the fourth corner (point A)? Express your answer in terms of the variables Q, L, and the Coulomb’s constant k.

A jumbo jet can fly its whole length in 20 seconds at a certain speed and has a 284-foot length. The big jet taxied completely past a 710-foot-long hangar in 70 seconds while travelling at the same speed.

In physics, you can get average speed by dividing the total distance travelled by the total time needed to travel that distance. Speed is the rate of change in an object's position, expressed in metres per second. The rate at which an object travels a distance is considered its speed. High speed describes an object that is travelling quickly.

P should represent the plane's length in feet.

20p = (710+p)/20p = 14200+20p 50p = 14200 p = 284ft

Learn more about speed here

https://brainly.com/question/28224010

#SPJ4

The plane's speed at the end of 10.0 seconds is 200 m/s and the distance it has travelled is 1750 meters.

The initial speed of the plane, u = 150 m/s

Acceleration of the plane, a = 5 m/s²

Time, t = 10 sec

We can find the plane's speed at the end of 10. 0 seconds by the formula

a = (v - u)/ t

⇒5 = (v - 150)/ 10

⇒50 = v - 150

⇒v = 150 + 50

⇒v = 200 m/s

Now, to find the distance it has travelled we will use the kinematic equation

v² = u² + 2as

⇒200² = 150 ² + 2 × 5 × s

⇒40000 = 22500 + 10s

⇒17500 = 10 s

⇒s = 1750 m

To know more about kinematic, here

https://brainly.com/question/28037202

#SPJ4

The time taken by the object to hit the ground is 1.8 seconds.

The attraction that draws two objects together is known as gravitational force, sometimes referred to as gravity. Every mass-containing object pulls on nearby things gravitationally in a sizable way.

The time it takes for an object to hit the ground after being dropped off a cliff can be calculated using the formula:

t = √(2*d/g)

where t is the time, d is the distance fallen, and g is the acceleration due to gravity.

In this case, we don't know the distance fell, but we can use the horizontal velocity and time of travel to find it:

d = v * t

where v is the velocity (6 m/s), and t is time (3 seconds)

d = 6 * 3 = 18 m

Now we can use the distance fallen to calculate the time it takes to hit the ground:

t = √(2*d/g)

g is approximately 9.8 m/s^2

t = √(2*18/9.8) = √ (3.6) = 1.8 seconds

So, it takes 1.8 seconds for the object to hit the ground after traveling horizontally off a cliff at 6 m/s for 3 seconds.

To know more about gravitational force, visit:

brainly.com/question/12528243

#SPJ1

The time it takes for the ball to reach its maximum height is 745 milliseconds.

What is time?

Time is defined as a scalar quantity that describes the progression of events in the universe. It is often considered to be the fourth dimension of spacetime, along with the three dimensions of space. Time is closely related to the concepts of causality, or the relationship between cause and effect, and is considered to be a fundamental aspect of the physical universe.

To find the time it takes for the ball to reach its maximum height, we need to use the equation:

1/2 * a * t^2 + v * t + d = 0

where a is the acceleration due to gravity (-9.8 m/s^2), t is the time, v is the initial velocity (2.13 m/s), and d is the initial displacement (0 m, since the ball is thrown upward from the ground).

We know that the ball is thrown upward and reaches its maximum height, so it is subject to a constant acceleration due to gravity in the downward direction. Therefore, the acceleration is -9.8 m/s^2.

The time to reach the maximum height can be found by solving the above equation for t.

t = sqrt(-2*d/(a+v))

t = sqrt(-2*0/(-9.8+2.13))

t = sqrt(2*2.13/(9.8-2.13))

t = sqrt(4.26/7.67)

t = sqrt(0.555)

t = 0.745s

To get the time in milliseconds:

t = 0.745s * 1000ms/s = 745 ms

Therefore, the time it takes for the ball to reach its maximum height is 745 milliseconds.

To learn more about time from the given link:

https://brainly.com/question/26046491

#SPJ4

Q is the charge's magnitude, V is its velocity, X is the angle formed by the magnetic field's direction and the charge's motion, and B is the strength of the magnetic field.

We must divide this amount by the mass of the charged particle or particles in order to determine the acceleration. Its speed at a later time is 1. 20 Mm/s (non relativistic because v is much less than the speed of light). When a refractive index diminishes over time, light shifts its frequency, which is referred to as photon acceleration [13,14]. Similar to charged particle acceleration, a rise in group velocity is accompanied by an increase in photon energy, or frequency.

Learn more about acceleration here-

https://brainly.com/question/12550364

#SPJ4

The truck bed and the crate's static coefficient of friction, assuming the crate doesn't slide, is 0.400.

Between the truck bed and the crate, there is 0.64 coefficient of static friction. When the bed is in the position depicted, the truck must move quickly to the right in order to make the crate slide.

The resistive friction force (Fr) divided by the normal or perpendicular pushing force (N) yields the coefficient of friction, which is a numerical value. The formula fr = Fr/N is used to represent it.

To know more about static friction visit:-

https://brainly.com/question/13000653

#SPJ4

The causes diffusion in cells are,  temperature, area of interaction, the size of the concentration gradient.

1) Temperature, The rate of diffusion increases as temperature rises.

2) Area of Interaction: The rate of diffusion increases as the surface area of interacting molecules increases.

3) The Size of the Concentration Gradient: The rate of diffusion is higher the greater the concentration gradient between the regions.

Higher the rate of diffusion, the more concentration between the locations. The movement is forced because of the increased pressure that the higher concentration creates. The movement of molecules from a location of higher concentration to a region of lower concentration can be used to define diffusion. The continuous motion (or kinetic energy) of atoms in matter is the primary cause of diffusion.

To know more about diffusion

https://brainly.com/question/28851242

#SPJ4

Interstitial lung disease is low lung compliance as a result, last of electrical lung tissue destruction.

Interstitial lung disorders brought on by breathing in particles like silicon and asbestos (asbestosis) can cause low lung compliance (silicosis).

Lungs and the pleural cavity have the capacity to expand and contract in response to variations in pressure. Lung compliance, which is a key determinant of lung health and function, is defined as the volume change per unit of pressure change across the lung. Lung compliance varies between inhalation and expiration because measurements of lung volumes vary between the two at the same pressure. Depending on whether only volume and pressure are measured (static) or whether their variations over time are also recorded, lung compliance can be classified as either static or dynamic.

know more about lungs here

https://brainly.com/question/13210870#

#SPJ4

The correct option is C ; Water vapor , Water vapour is water that is gaseous rather than liquid. It can be generated by either evaporation or sublimation.

Water vapour, unlike clouds, fog, or mist, which are just suspended particles of liquid water in the air, cannot be seen since it is in gaseous form.

Water vapor has the same chemical formula as regular water - H2O - but the water molecules in vapor interact with each other less and are not as organized as they are in water and ice. Pressure, temperature, and relative humidity all influence whether water is liquid or gas.

Learn more about to Water vapor

https://brainly.com/question/14529481

#SPJ4

A 1.5 x 103 kg car's momentum is equal to 4.5 x 104 kg m/s east if it moves at a speed of 30 m/s for 60 seconds while traveling straight east.

Momentum is a property of an object or system that describes its tendency to move or stay in motion. It is equal to the product of the mass of the object and its velocity. Momentum is conserved, meaning that the total momentum of an isolated system remains constant, regardless of any changes or interactions within the system. Momentum is an important concept in classical mechanics, and is directly related to forces, energy, and angular momentum. Momentum is an essential factor for describing the behavior of objects in motion.

To learn more momentum

https://brainly.com/question/1042017

#SPJ1

Answer:

Below

Explanation:

Mech adv = effort arm / load arm = 15 / 5 = 3

To solve this we must be knowing each and every concept related to force. and its different types. Therefore,  the mechanical advantage is 3.

A force is an outside entity that has the power to alter a body's state of rest or motion. It has a direction and a magnitude. The point where forces are applied is determined either by the force's direction as well as the application of the force.

Your training at this level should place a major emphasis on the idea which a push or even a pull was refereed to as a force. In our daily lives, forces appear in a variety of ways. as in weight and power. It refers to the force a bat applies to a ball and the strength a hairbrush has when stroking hair.

Mech adv = effort arm / load arm = 15 / 5 = 3

Therefore,  the mechanical advantage is 3.

To know more about force, here:

https://brainly.com/question/13014979

#SPJ2

Deoxyribonucleic acid is a polymer composed of two polynucleotide chains that coil around each other to form a double helix.

A nonsense mutation occurs in the DNA when a sequence changes itself and gives rise to a stop codon rather than a codon specifying an amino acid. The presence of the new stop codon results in the production of a shortened protein that is non-functional.

A nonsense mutation is also known as base substitution which results in a stop codon in such a position from where there was not one before, which causes the premature termination of protein synthesis and, more than likely, a complete loss of function in the finished protein.

So we can conclude that a nonsense mutation always causes a loss of amino acids.

Learn more about DNA here: https://brainly.com/question/16099437

#SPJ1

The above prompt is related to Interplanetary Science or Astronomy.

1) The diagram that best represents the appearance of the Moon at position P 'When viewed from the Earth is Option A.

2) The factor that most likely caused the difference in the apparent size of the Moon in photographs A and B is: "The distance from the Earth to the Moon changed." (Option D).

The study of planets and other objects in our solar system is known as interplanetary science. Telescopes, satellites, and other technologies are used by scientists to understand more about these objects and how they developed and evolved through time.

It also entails researching the possibility of life on other planets and moons, as well as learning about the solar system's past and future.

Learn more about Interplanetary Science:
https://brainly.com/question/858650
#SPJ1

Answer: The time it took for them to fall ere the same.

Explanation:

The only difference was because of resistance, weight doesn't affect the speed of gravity, the speed of gravity stays the same (9.801 meters per second)

L=rp Angular Momentum the linear momentum p. Moment of momentum is another name for angular momentum.

List the object's mass and speed in step one. Convert any values into SI units in step two (kg, m, s). Step 3: To calculate an object's momentum, multiply the object's mass and velocity.

Momentum can go wrong. As a vector quantity with both magnitude and direction, momentum has both. The sign, positive or negative, in physics serves as a cue as to the direction. Positive amounts normally signify a forward or upward motion, whereas negative quantities typically indicate a backward or downward motion.

to know more about momentum here:

brainly.com/question/24030570

#SPJ4

What is momentum?

At the instant when a mass is at its equilibrium position when undergoing simple harmonic motion, its instantaneous velocity is its maximum.

Therefore the answer is C. At equilibrium, its instantaneous velocity is at maximum

The simple harmonic motion is periodic motion that oscillates around an equilibrium position. At the equilibrium position, the net force on the mass is zero. Therefore, the mass is not accelerating, so its instantaneous acceleration is zero.

The motion is periodic, meaning it repeats itself at regular intervals of time. In the case of a mass on the end of a spring, the spring exerts a force on the mass that acts to bring it back to its equilibrium position. When the mass is at the equilibrium position, the spring force is zero, and the mass is not accelerating. Therefore, the acceleration is maximum at it ends and decreases to zero at equilibrium position.

The instantaneous velocity is zero at the end as it changes direction of motion, though the acceleration is decreasing from end position to equilibrium, velocity is increasing. The instant after equilibrium position, the acceleration is in opposite direction decreasing the velocity till it is zero at the end position.

To know more on SHM

https://brainly.com/question/29183311

#SPJ4

Amplification is the term used to describe how far the particles are pushed from their initial position.

How closely molecules are packed together is determined by density. Because air is a gas, its molecules may either pack closely or spread widely. Higher up, less air is pressing down from above, and gravity is less away from the center of the Earth.

Longitudinal waves are what makeup sound. Compressions and rarefactions are also present in longitudinal waves when they pass through any given material. When particles travel in close proximity to one another, compression occurs, generating areas of intense pressure.

To know more about Amplifications visit:

brainly.com/question/16133707

#SPJ4

A) A parcel of air will rise if it has a lower density than the surrounding air.  is the relative order of air in the atmosphere.

In the atmosphere, air moves from high pressure to low pressure areas. When a parcel of air is heated, it expands and becomes less dense than the surrounding air. As a result, the parcel of air rises because it is less dense than the surrounding air, which creates a lower pressure area.

This process is known as convection and is responsible for many weather phenomena such as thunderstorms and cloud formation. In contrast, if a parcel of air cools and becomes more dense, it sinks because it creates a higher pressure area than the surrounding air.

To know more about   convection click below:

https://brainly.com/question/4138428#

#SPJ4

A radio message is sent home by astronauts in a spaceship approaching Mars at a distance of from Earth.

A contact from Mars travels [between 3 and 22] minutes at light speed to reach Earth. Relativity contributes to the fact that the distance between Earth and Mars is 1.26 seconds longer.

A Mars year is roughly equivalent to two Earth years because of Mars' nearly two-fold longer orbital period than the Earth's. Earth and Mars are 57.6 million kilometers (35.8 million miles) from one another, while 401 million kilometers separate them at their farthest point (249 million mi).

The sole means of contact between Earth and Mars are radio and messenger. A courier will undoubtedly require a lot of time. We can determine how long it will take a radio message to travel between the two planets since radio waves travel at the speed of light (299,792 km/s; 186,282 mi/s). When the two planets are at their closest, the one-way voyage takes the fewest amount of time—3.2 minutes.

The time required for a one-way trip is 22.3 minutes when they are the furthest apart. A round-trip message will take between 6.4 and 44.6 minutes to send and receive. Of course, receiving an answer will take the same amount of time in each situation.

Learn more about Contact here:

https://brainly.com/question/3966206

#SPJ4

Using the strain energy that the pole has stored in it, the running athlete's kinetic energy is transformed into the potential energy needed to jump.

Males employ the formula: h= 0.60 * [male height] + 12(v2/g), whereas females use h= 0.55 * [female height] + 12(v2/g).

It is merely an instance of energy being exchanged. If an athlete can run at 10 m/s and we calculate g as 10 m/s/s, the height equals 5 m.

Each vaulter has three tries to clear a particular height during a competition. In order to fall readily if touched, a bar is supported by two uprights. Up until a winner is determined through the process of elimination, it is raised gradually.

There has been a failed trial. A competitor's pole breaking while trying to clear the bar is not considered a trial or failure. No one is permitted to touch the vaulting pole.

To learn more about pole refer to:

https://brainly.com/question/3506806

#SPJ4

Accenture can assist its clients in being more sustainable thanks to the myNav. By making it easier to create cloud solutions that lower carbon emissions by rearranging manufacturing facilities such that carbon emissions can be calculated with ease.

by establishing new corporate efforts to lower transportation expenses and by establishing new rules for the disposal of out-of-date technology.

Accenture can assist its clients in becoming more sustainable by using mynav to locate, assess, architect, and simulate an end-to-end solution at scale.

reduces the expense of transportation

creates a design that is appropriate and aids the customer in becoming more sustainable.

establishes sustainable guidelines for disposing of outdated technology.

myNav Green Cloud Advisor assists businesses in developing cloud solutions that cut carbon emissions and create a platform for ethical innovation. Green Cloud Advisor starts by establishing a baseline for the energy usage, compute needs, and sustainability objectives of current data centers. through promoting the development of cloud technologies that cut down on carbon emissions

To learn more about Accenture myNav from given link

https://brainly.com/question/26449898

#SPJ4

The acceleration in Case A is four times that of Case B.

Acceleration is the rate of change of velocity of an object. It is the measure of how quickly an object changes its velocity over time, represented by the equation a = (v-u)/t, where a is the acceleration, v is the final velocity, u is the initial velocity, and t is the time. Acceleration can be either positive or negative; a positive acceleration indicates an increase in velocity while a negative acceleration indicates a decrease in velocity.

This is because the acceleration of an object in uniform circular motion is given by the equation a = v^2/r, where a is the acceleration, v is the speed, and r is the radius of the circle. Because the speed in Case A is half that of Case B, the acceleration will be one-fourth that of Case B. However, because the radius in Case A is two times that of Case B, the acceleration will be four times that of Case B.

To learn more about acceleration
https://brainly.com/question/26588495
#SPJ1

These tides occur twice each lunar month throughout the entire year. When the earth, moon, and sun are all in alignment, neap tides are produced by the sun's gravitational pull amplifying that of the moon.

Instead, the phrase refers to the idea of the tide "springing forth." Regardless of the season, spring tides happen twice each lunar month. Neap tides happen when the sun and moon are at right angles to one another, which also happens twice a month.

The sun, the form of the ocean, and the moon all have an impact on how much or little the tide rises or falls on Earth. Moon tides are the results of the moon's influence on the Earth's tides. The major subject of this article is moon tides.

To learn more about tides visit:

brainly.com/question/9493666

#SPJ4

The correct option is B, The electron's speed at f is equal to its speed at i.

Electrons are subatomic particles that are found in atoms. They are the negatively charged particles that orbit the nucleus of the atom, and they have an extremely small mass. Electrons travel at different speeds depending on their energy level. At their lowest energy level, electrons move at an extremely slow speed, about one thousandth of the speed of light. As the electrons gain energy, their speed increases.

In a vacuum, when electrons have the highest energy level, they can travel at a speed of nearly the speed of light, which is around 186,000 miles per second. In a vacuum, the electrons would have the same speed regardless of their mass. Electrons also move slower inside a material, such as a metal, due to the presence of other atoms. Electrons in metals usually move at a speed of about 1/10th the speed of light. This slower speed is due to the electrons having to pass through energy barriers created by the other atoms in the metal. In general, electrons are very fast particles that can travel at speeds up to nearly the speed of light.

To learn more about Electron's speed visit here:

brainly.com/question/14827627

#SPJ4

0.08 m/s2 is the average acceleration. The acceleration's degree of uncertainty is 0.0135 m/s2.

Accelerations are included in vector quantities. An object's acceleration in relation to a net force is determined by the direction of that force. Force imbalances lead to acceleration in a body.

Uniform, non-uniform, and average acceleration are the three primary types of accelerated motions. It is said to have uniform acceleration when an object moves in a straight line with an increase in speed that happens at regular intervals of time.

Acceleration is the term used to describe any change in the speed or direction of a motion. Anything that is accelerating is moving faster, slower, or in a direction other than straight forward.

To learn more about acceleration visit:

brainly.com/question/12550364

#SPJ4

Statement D. They have sufficient gravity to make themselves round accurately describes a similarity between all planets in terms of this movement and the presence of mass to form such a celestial body.

All planets need to have gravity in order to orbit around major celestial bodies, i.e., stars such as in the case of the earth planet or Mars, they orbit around the Sun which is the star of the solar system. The presence of the attractive force of gravity allows planets to move in a cycle across their stars.

Therefore, with this data, we can see that all planets have gravity and orbit around major celestial bodies and thus they can be considered to share the particularity to have a well defined orbit due to the presence of mass.

Learn more about planets and gravity here:

https://brainly.com/question/1286910

#SPJ1

In this case, a body of mass 5 kg kept at a height of 10 m. So, the potential energy is given as 500 J.

An object's potential energy is its stored energy. This energy has the capacity to be productive. An object's potential energy is provided by gravity. Gravity's downward force is the source of this potential energy.

The acceleration brought on by gravity is known as the gravitational constant, or g. On Earth, this acceleration is equivalent to 10 metres per second. PE = mgh is the equation for potential energy resulting from gravity. The object's potential energy declines and its kinetic energy rises as it approaches the ground.

Potential Energy = 5 x 10 x 10 = 500J.

To learn more about Potential Energy visit:

brainly.com/question/24284560

#SPJ4

Answer:

The acceleration of an object can be calculated using Newton's second law of motion, which states that the force acting on an object is equal to the mass of the object multiplied by its acceleration. The equation is:

F = ma

where F is the force, m is the mass, and a is the acceleration.

So, if we know the mass of the object (m = 56 kg) and the force acting on it (F = 800 N), we can calculate the acceleration (a) by dividing the force by the mass:

a = F / m

a = 800 N / 56 kg

a = 14.28 m/s^2

So the acceleration is 14.28 m/s^2

By using the formulae, λ = h/mv, The De Broglie wavelength of the muon is calculated to be 4.13 × 10^10 m, as according to the given data in the question.

The shortest measured time is 100 attoseconds. A quadrillionth of a minute is a femtosecond. One quadrillionth of a minute is a picosecond. One quadrillionth of a second is a nanosecond.

Particles are smaller than just a nanometer. Depending on the element, an atom is between 0.1 and 0.3 nm in size. Atoms on the a surface in a SEM image.

To know more about Particles visit:

brainly.com/question/1685421

#SPJ4

When you touch a piece of wool against your skin, your skin acquires a negative charge because of the conservation of charge, which caused it to gain a positive charge.

Charge is a material's property that can be transferred into another person's body. The transfer of the charge results in the generation of electricity. The following are some examples of charge's various properties: 1 Electric charge addition 2 Electric charge conservation 3 Electric charge quantization. Equations in chemistry are denoted by the capital letter Q to denote charge, with the elementary charge of an electron (e) serving as a standard unit. The coulomb is the SI-derived unit of charge (C). In electrical engineering, the ampere-hour (Ah) unit of charge is frequently used.Dipole Definition in Chemistry and Physics. by this primary information we can consider that when you rub a piece of wool upon your skin and your skin becomes negatively charged because it gained a positive charge as the result of conservation of charge.

Learn more about Charge:

brainly.com/question/3412043

#SPJ4