Answer:
This question is not complete but the completed question is below
Which statement is not correct for lamps connected in parallel?
A They can be switched on and off separately.
B They will remain bright if another lamp is connected in parallel.
C They share the supply voltage equally between them.
D They still operate if one lamp is removed.
The correct option is A
Explanation:
Lamps connected in series have the same voltage running across each lamp in the connection and will thus have the same brightness if any lamp is added or removed. This property also means they can only be switched on and off by a single switch, hence option A is not correct about lamps connected in parallel.
Lamps connected in a parallel circuit will have the same voltage and different current.
A parallel circuit contains resistors arranged parallel to each other. some basic characteristics of parallel circuit include the following;
the voltage in all the resistors is the samethe current flowing in each resistor is differentV = I₁R₁ + I₂R₂ + I₃R₃ + ---
where;
V is the voltage in the circuitI is the different currentsR is the different resistorsThus, we can that lamps connected in a parallel circuit will have the same voltage and different current.
Learn more about parallel circuit here: https://brainly.com/question/12739827
write an email to your friend about your
preparation for the upcoming exam
Answer:
You will be very glad to know that my preparation for HSC examination is very good. I have prepared myself for the HSC Examination 2015. I am confident that I will obtain very good marks in the examination. I have revised them several times and I am hopeful of obtaining distinction marks in all the subjects.
Explanation:
This is from Brainly hope this person helped you
What is the result of increasing the speed at which a magnet moves in and
out of a wire coil?
O A. The current in the wire increases.
B. The magnetic field around the magnet decreases.
C. The current in the wire decreases.
O D. The magnetic field around the magnet increases.
Answer:
Explanatio
Increasing the speed of the relative motion between the coil and the magnet – If the same coil of wire passed through the same magnetic field but its speed or velocity is increased, the wire will cut the lines of flux at a faster rate so more induced emf would be produced. 3)n:
Which is the BEST example of selective attention?
Answer:
Examples include listening carefully to what someone is saying while ignoring other conversations in a room (the cocktail party effect) or listening to a cell phone conversation while driving a car. Attention is one of the most intensely studied topics within psychology and cognitive neuroscience.
A rolling ball moves from x1 = 8.0 cm to x2 = -4.1 cm during the time from t1 = 2.9 s to t2 = 6.0 s .
Complete Question
A rolling ball moves from [tex]x_1 = 8.0 \ cm[/tex] to [tex]x_2 = - 4.1 \ cm[/tex] during the time from [tex]t_1 = 2.9 s[/tex] to [tex]t_2 = 6.0s[/tex]
What is its average velocity over this time interval?
Answer:
The velocity is [tex]v = 3.903 \ m/s[/tex]
Explanation:
From the question we are told that
The first position of the ball is [tex]x_1 = 8.0 \ cm[/tex]
The second position of the ball is [tex]x_2 = - 4.1 \ cm[/tex]
Generally the average velocity is mathematically represented as
[tex]v = \frac{ x_1 - x_2}{t_2 - t_1}[/tex]
=> [tex]v = \frac{ 8 - -4.1 }{ 6 - 2.9 }[/tex]
=> [tex]v = 3.903 \ m/s[/tex]
A vehicle travels with an average speed of sav = 15 mi/hr.
A car travels 23.0 m/s for 1.0 hours and then accelerates for 30.0 seconds to reach 40.0 m/s. What was the total distance traveled by this car
Answer:
s = 83.85 km
Explanation:
First we calculate the distance covered by car, while traveling at constant speed:
s₁ = v₁t₁
where,
s₁ = distance covered at constant speed = ?
v₁ = constant speed = 23 m/s
t₁ = time of travel at constant speed = 1 hr = 3600 s
Therefore,
s₁ = (23 m/s)(3600 s)
s₁ = 82800 m = 82.8 km
Now, we calculate the distance travelled in accelerated motion. First we use 1st equation of motion to find acceleration:
Vf = Vi + at₂
where,
Vf = Final velocity = 40 m/s
Vi = Initial Velocity = 30 m/s
a = acceleration = ?
t₂ = time = 30 s
Therefore,
40 m/s = 30 m/s + a(30 s)
a = 10 m/s/30 s
a = 0.33 m/s²
Now, we use 2nd equation of motion for distance:
s₂ = Vi t₂ + (1/2)at₂²
s₂ = (30 m/s)(30 s) + (1/2)(0.33 m/s²)(30 s)²
s₂ = 900 m + 150 m
s₂ = 1050 m = 1.05 km
So, the total distance covered was:
s = s₁ + s₂
s = 82.8 km + 1.05 km
s = 83.85 km
PLEASE HELP
What are the most common limiting factors in a cloud forest ecosystem?
What are the most common limiting factors in a coral reef ecosystem?
What are the most common limiting factors in a desert ecosystem?
What is an abiotic infectious agent?
Name five types of bacteria.
A car weighing 1,356 N is speeding down a highway with a velocity of 83 km/h. What is the momentum of this car
Answer:
The momentum of the car is 3190.74 kgm/s
Explanation:
Given;
weight of the car, w = 1,356 N
velocity of the car, v = 83 km/h = 23.06 m/s
The mass of the car is given by;
m = w/g
where;
g is acceleration due to gravity = 9.8 m/s²
m = 1356 / 9.8
m = 138.367 kg
The momentum of this car is given by;
P = mv
P = (138.367 x 23.06)
P = 3190.74 kgm/s
Therefore, the momentum of the car is 3190.74 kgm/s
In the pictire ,can we separate hydrogen (H) from oxygen (O)?
Paanswer nga po.....
A.)
Water is the name of the pure substance H₂O
B.)
Hydrogen and Oxygen are the compound of water
C.)
Yes, we can
D.)
This process known as Electrolysis
Suppose you have a 2000 Watt water heater that is on for a total of 150 hours a month. How much will this cost you at a rate of 10 cents per kW*hr?
Answer:
$30
Explanation:
Given that,
Power of a water heater, P = 2000 Watts
It is on for a total of 150 hours a month.
2000 Watts = 2 kW
Time, t = 150 hours
Energy used by the water heater is given by :
[tex]E=P\times t\\\\E=2\ kW\times 150\ h\\\\E=300\ kWh[/tex]
It is also mentioned that the cost is 10 cents per kWhr.
Since, $1 = 100 cents
10 cents = $0.1
So, the total cost for the month is :
Cost = 300 × 0.1
Cost = $30
So, the required cost is $30.
What is Hydroelectric energy used for? Use in your own words.
What does the underlined word mean in the following sentence? El conejo viene el día de Pascua de Resurrección. Easter Christmas Holidays Thanksgiving
Answer:easter
Explanation:
Answer:
Easter
Explanation:
did it on edge, and searched it up
A 0.200 H inductor is connected in series with a 88.0 Ω resistor and an ac source. The voltage across the inductor is vL=−(12.0V)sin[(487rad/s)t].
Required:
a. Derive an expression for the voltage vR across the resistor. Express your answer in terms of the variables L, R, VL (amplitude of the voltage across the inductor), ω, and t .
b. What is vR at 2.00 ms? Express your answer with the appropriate units.
Answer:
a. (VL)R/ωL[1 - cos[ωt]] = (10.84 V)[1 - cos[(487rad/s)t]]
b. 1.084 mV
Explanation:
a. Since it is a series circuit, the current in the inductor is the same as the current in the resistor.
Now, the voltage across the inductor vL = -Ldi/dt.
So, the current, i = -1/L∫vLdt.
Now, vL = −(12.0V)sin[(487rad/s)t] and L = 0.200 H
Substituting these into i, we have
i = -1/L∫vLdt
= -1/0.200H∫[−(12.0V)sin[(487rad/s)t]]dt.
= -[−(12.0V)]/0.200H∫[sin[(487rad/s)t]]dt.
= 60V/H∫[sin[(487rad/s)t]]dt
Integrating i, we have
i = 60V/H ÷ [(487rad/s)[-cos[(487rad/s)t]] + C
at t = 0, i(0) = 0
0 = 60V/H ÷ [(487rad/s)[-cos[(487rad/s)× 0]] + C
0 = 60V/H ÷ [(487rad/s)[-cos[0]] + C
0 = 60V/H ÷ [(487rad/s)[-1]+ C
C = 60V/H ÷ [(487rad/s)
So, i = 60V/H ÷ [(487rad/s)[-cos[(487rad/s)t]] + 60V/H ÷ [(487rad/s)
i = 60V/H ÷ [(487rad/s)[1 - cos[(487rad/s)t]]
i = (0.123A)[1 - cos[(487rad/s)t]] = VL/ωL[1 - cos[ωt]] where ω = 487rad/s and VL = 12.0 V and L = 0.200 H
So, the voltage across the resistor vR = iR where R = resistance of resistor = 88.0 Ω
So, vR = iR = VL/ωL[1 - cos[ωt]] × R = (VL)R/ωL[1 - cos[ωt]]
= (0.123A)[1 - cos[(487rad/s)t]] × 88.0 Ω
= (10.84 V)[1 - cos[(487rad/s)t]]
b. vR at t = 2.00 ms = 0.002 s
So, vR = (10.84 V)[1 - cos[(487rad/s)(0.002)]]
= (10.84 V)[1 - cos[0.974]]
= (10.84 V)[1 - 0.9999]
= (10.84 V)(0.0001)
= 0.001084
= 1.084 mV
A rocket traveling at 36.96 m/s is accelerated uniformly to 74.44 m/s over a 21.37 s interval. What is its displacement during this time?
Answer:
s = 1190.3 m = 1.19 km
Explanation:
First we find the acceleration by using first equation of motion:
Vf = Vi + at
where,
Vf = Final Velocity = 74.44 m/s
Vi = Initial Velocity = 36.96 m/s
a = acceleration = ?
t = time = 21.37 s
Therefore,
74.44 m/s = 36.96 m/s + a(21.37 s)
a = (74.44 m/s - 36.96 m/s)/21.37 s
a = 1.75 m/s²
Now, we use 2nd equation of motion to find distance covered (s):
s = Vi t + (1/2)at²
s = (36.96 m/s)(21.37 s) + (1/2)(1.75 m/s²)(21.37 s)²
s = 789.83 m + 400.47 m
s = 1190.3 m = 1.19 km
A jet airplane with a 75.0 m wingspan is flying at 260 m/s. What emf is induced between the wing tips in V if the vertical component of the Earth’s magnetic field is 3.00 × 10-5 T?
Answer:
0.585V
Explanation:
Given that:
B = 3.00 × 10-5 T
l = 75.0 m
v = 260 m/s
From Blv = emf between the wing tips
= 3.00 × 10-5 T × 75×260
= 117/200
= 0.585V
Hence, the emf between the wing tips is 0.585V
An ant is crawling along a yardstick that is pointed with the O-inch mark to the east and the 36-Inch mark to the west. It starts at the 19-inch mark, crawls to the 27-inch
mark, then moves to the 7-inch mark. What was the total distance the ant traveled?
Answer:
33 Inches
Explanation:
The movement of the ant is sketched in the attached image. The ant moved from the 19-inch mark to 27-inch mark covering a distance of 13 Inches (27 - 19). Finally, it moved from the 27-inch mark to 7-inch mark covering a distance of 20 Inches (27 - 7).
Total Distance covered = 13 + 20 = 33 Inches.
Hence, the total distance the ant traveled is 33 Inches.
Does anyone skateboard still?
Answer:
yes
Explanation:
people still skateboard that is an easy question
A car covers a distance of 200m. If its velocity is 20 m/s, calculate the time taken.
Answer:
10 seconds
Explanation:
velocity=displacement/timeI want to know about the inventions caused due to rain. Like the Benjamin Franklin's Lightning Conductor. I have to make a chart.
(b) In the USA, drones are not allowed to be flown too high above the ground.
Suggest one possible risk of flying a drone too high above the ground.
Plz complete thank you in advance
The 400-foot altitude limit was put in place for the sake of airspace safety, and there is a risk to country security as well as the privacy of citizens.
What are drones?Unmanned aerial vehicles (UAVs), sometimes known as drones, are used for a variety of jobs, from routine to extremely dangerous. These robotic-looking planes can be seen practically everywhere, from delivering groceries to your home to rescuing avalanche victims.
The 400-foot altitude restriction was ultimately implemented for airspace safety. Given the breadth of the airspace above 400 feet, the likelihood of a drone colliding with a human aircraft is exceedingly remote, but the consequences might be disastrous.
Any aerial vehicle that uses software to fly autonomously or that may be controlled remotely by a pilot is referred to as a drone. Numerous drones come equipped with cameras to gather visual data and propellers to stabilize flying paths. Drone technology has been incorporated into industries like videography, search and rescue, agriculture, and transportation.
When in uncontrolled (Class G) airspace, your drone must be flown 400 feet above the ground or less.
To know more about drones:
https://brainly.com/question/27753670
#SPJ2
What did Isaac Newton’s investigation if the gravity explain ?
Answer:
Gravity acts on all objects in the universe.
Explanation:
A college student has just bought a small computer that weighs 50N. Her apartment is on the 5th floor which is 35 meters up. How much work must she do to drag her computer up the stairs?
Answer:
W = 1750 J
Explanation:
It is given that,
Weight of a computer, F = 50 N
A student wants to keep it on the 5th floor which is 35 meters up.
We need to find the work done by her to drag her computer up the stairs. Let it is W. Using the formula of work as follows :
W = F d
Put all the values,
W = 50 N × 35 m
W = 1750 J
So, 1750 J of work is done by her to drag the computer up the stairs.
A 50 g mass is freely hanging from a horizontal meter stick at a distance of 99 cm from the pivot. Calculate the weight force W that the mass exerts on the meter stick? ·Calculate the torque that the weight force exerts about the pivot? 4. What does the pivot exert on the meter stick?
Answer:
W = 0.49 N
τ = 0.4851 Nm
Force
Explanation:
The weight force can be found as:
W = mg
W = (0.05 kg)(9.8 m/s²)
W = 0.49 N
The torque about the pivot can be found as:
τ = W*d
where,
τ = torque
d = distance between weight and pivot = 99 cm = 0.99 m
Therefore,
τ = (0.49 N)(0.99 m)
τ = 0.4851 Nm
The pivot exerts a FORCE on the meter stick because the pivot applies force normally over the stick and has a zero distance from stick.
5.
An 80 newton force and a 45 newton force act on an object
as shown below.
80 N
30°
4S N
Which of the following vectors would bets represent an
equilibrant when added to this system?
(1) 24 N to the left (3) 24 N to the right
(2) 114 N to the right (4) 45 N to the left
Tirant Showroiculations
Answer:
the answer is a time your welcome
Answer:
(1)
Explanation:
Light passes through a 0.15 mm-wide slit and forms a diffraction pattern on a screen 1.25 m behind the slit. The width of the central maximum is 0.75 cm. What is the wavelength of the light?
a. 400nm
b. 450nm
c. 510nm
d. 600nm
Answer:
b. 450 nm
Explanation:
The wavelength of light can be calculated by using the formula derived in Young's double slit experiment. The formula is as follows:
Δx = λL/d
Δx/2 = λL/2d
where,
Δx/2 = half distance between consecutive dark fringes = width of central maximum = 0.75 cm = 0.0075 m
λ = wavelength of light = ?
L = Distance of Screen = 1.25 m
d = width of slit = 0.15 mm = 0.00015 m
Therefore,
0.0075 m = λ(1.25 m)/(0.00015 m)
λ = (0.0075 m)(0.00015 m)/2(1.25 m)
λ = 4.5 x 10⁻⁷ m = 450 nm
Thus, the correct option is:
b. 450 nm
A typical atomic polarizability is 1 × 10-40 (C·m)/(N/C). If the q in p = qs is equal to the proton charge e, what charge separation s could you produce in a typical atom by applying
Answer:
s = 6.25 10⁻²² m
Explanation:
Polarizability is the separation of electric charges in a structure, in the case of the atom it is the result of the separation of positive charges in the nucleus and the electrons in their orbits, macroscopically it is approximated by
p = q s
s = p / q
let's calculate
s = 1 10⁻⁴⁰ / 1.6 10⁻¹⁹
s = 0.625 10⁻²¹ m
s = 6.25 10⁻²² m
We see that the result is much smaller than the size of the atom, therefore this simplistic model cannot be taken to an atomic scale.
differences between a resultant and a equilibrium
Answer:
I found "As nouns the difference between resultant and equilibrium is that resultant is anything that results from something else; an outcome while equilibrium is the condition of a system in which competing influences are balanced, resulting in no net change. is following as a result or consequence of something."
Explanation:
A jogger runs north 6 km, 5 km east, and 4 km north again. Time is 1.9 hr. What is average velocity?
Answer:
Average velocity = 5.9 km/ hr (or 1.64 m/s).
Explanation:
Velocity = [tex]\frac{displacement}{time}[/tex]
It is a vector quantity and has an SI unit of m/s.
Displacement = [tex]\sqrt{x^{2} + y^{2} }[/tex]
x = 5 km east
y = 6 km north + 4 km north
= 10 km north
So that,
Displacement = [tex]\sqrt{5^{2} + 10^{2} }[/tex]
= [tex]\sqrt{25 + 100}[/tex]
= [tex]\sqrt{125}[/tex]
= 11.1803
Displacement = 11.18 km = 11180 m
Time = 1.9 hr = 6840 seconds
Average velocity = [tex]\frac{11.180}{1.9}[/tex]
= 5.8842
Average velocity = 5.9 km/ hr
The average velocity is 5.9 km/ hr (or 1.64 m/s).
a 1000kg car uses a breaking force of 10,000N to stop in two second. What is the change in momentum of the car?
Answer:
ΔP = 20000 N s
Explanation:
To solve this problem we use the relation between momentum and moment
I = Δp
let's calculate the momentum
I = ∫F dt
if we use the average force
I = F t
I = 10000 2
I = 20000 N s
therefore with the first equation
ΔP = I = 20000 N s
Which of the following would probably need the greatest force to overcome its inertia?
option 1 a tennis ball 2 a sports ar 3 a dump truck and four a bicycle
Answer:
A dump truck.
Explanation:
Inertia can be defined as the tendency of an object or a body to continue in its state of motion or remain at rest unless acted upon by an external force.
In physics, Sir Isaac Newton's first law of motion is known as law of inertia and it states that, an object or a physical body in motion will continue in its state of motion at continuous velocity (the same speed and direction) or, if at rest, will remain at rest unless acted upon by an external force.
Mathematically, it is given by the formula;
[tex] F = ma[/tex]
Where;
F represents force measured in Newton.m represents the mass of an object measured in kilograms.a represents acceleration measured in meter per seconds square.The inertia of an object such as a tractor trailer rig is greatly dependent or influenced by its mass; the higher quantity of matter in a dump truck, the greater will be its tendency to continuously remain at rest.
Hence, a dump truck would probably need the greatest force to overcome its inertia because it has more mass than all the other objects in the category. Also, the mass of an object is directly proportional to its inertia, as well as the force applied.
Answer:As one of Newton's Laws of Gravitational force The answer would Be a dump truck because it includes one of Newton's Laws of Gravitational force in the abstract Laws of gravity.